Recent content by Sygnus

  1. S

    Tunze 9012 DC performance

    Hi ! I've been using the Tunze 9012 DC for cca 2 years, in the first 5-6 month i can run at 20-30 % , beacuse its overflowing, I always need to increase the skimmer performance. Now its run at 100% , and dont have a strong foam. (completely disassembled and cleaned) Is something need replace...
  2. S

    Tunze 3162 and 3163

    I understand, then I will not replace it ! Thanks for the help !
  3. S

    Tunze 3162 and 3163

    Hi ! Can i replace in the 3163 the 6015 pump to the 6055 ? I will use the 6055 at 20V - 65-70 % , maybe at thunderstorm 100 %. It will work, or too much flow for the filter ?
  4. S

    Tunze "fish care" ?

    Thank You for the info ! Yes, the 6055 make big flow at feed pause, my oldest pump. I will watch the another 3, they are newer. Thank you, so i can see the difference now between the 2 9012 motor. I have the 9012DC, so i need the 9012.041 electronic foamer!
  5. S

    Tunze "fish care" ?

    Hi ! I have 2 x Tunze 6055 + 2 X Tunze 6095 and at only 1 - 6055 working the "fish Care" function...." the pumps will start up automatically after a delay of 20 seconds. The pump driver has been provided with a fish care function, which causes a revolution of the propeller every twenty...
  6. S

    Tunze 9006 / 9011

    Yes, its working now very good ! Thanks for the help !
  7. S

    Tunze 9006 / 9011

    I changed the reefpack 505 to one new 9012 DC ....fantastic skimmer, seriously, I really like it right now, make a very good foam. Working only 2 days ago at the minimum speed, i dont have problem with micro bubbles or anything, but not taking the scum from the surface. The grill only 1/3...
  8. S

    Tunze 9006 / 9011

    Im go the 9006 impeller in the 9011 motor, and the 9006 house with collection cup. The skimming looks good, but the foam does not pass through the roof, 1 week and cca 50ml skimmate, I think this is not enough. The screw 4 + 1/2 opened, make picture and video...
  9. S

    Tunze 9006 / 9011

    Ok, thank you for the help !
  10. S

    Tunze 9006 / 9011

    Thanks for the info ! This its the round 9006 motor, dont see any problem on the shaft / drive unit. I think i'm use the 9011 motor with the 9011 drive unit in the 9006 body and the 9006 collection cup...it will not raise too much foam ?
  11. S

    Tunze 9006 / 9011

    Hello, I would like to ask for help. I have Tunze 9006 that stop work. I can see that the rotor stops for a moment and then spins again, very low foam is formed...the rotor is defective or the motor block ? I have one 9011 reserve, but it does not fit under the hood....can i use the 9011...
  12. S

    Tunze 8850 led blinking

    Thank You for the answear ! This is only annoying when the moon phase is 4-5% and about 1% of the light is flashing, then it will blink.
  13. S

    Tunze 8850 led blinking

    Hi ! I have problem with my Tunze 8850 led, it starts flashing at the lowest strength. I'm using with 7097 controller. When start dimming flashing, when i'm set any channel 1% its flashing, above dont have this problem.... I want moonlight to use 1%, but I do not know because it flashes. Is...
Top