tunze nanostreams and profilux 3.1nex

herbklee

Member
hi,
can someone show me step by step how to connect and program my 2 tunze 6095s with m my profilux 3?
I can't find any clear info anywhere.

The pumps are both currently connected to my profilux via the tunze 1 and 2 cables via YL2 splitter to the L1 socket on my profilux.
TY
 
1. Go to the 1-10v interface settings and set L1 and L2 to "Stream pump" and voltage to 3-8V.
2. Go to the Stream settings located in the Extras section and assign the pumps to a group. If you want to have both pumps on the same group, select a pump group and assign the pumps to that group.
3. Program the pumps in the same screen and click save.

Just remember that Tunze 1 will function for "Odd" numbered L channels and T2 for "Even" numbered L channels.
 
1. Go to the 1-10v interface settings and set L1 and L2 to "Stream pump" and voltage to 3-8V.
2. Go to the Stream settings located in the Extras section and assign the pumps to a group. If you want to have both pumps on the same group, select a pump group and assign the pumps to that group.
3. Program the pumps in the same screen and click save.

Just remember that Tunze 1 will function for "Odd" numbered L channels and T2 for "Even" numbered L channels.



Thanks!




Sent from my iPhone using Tapatalk
 
Any pointers on how to program pumps in alternating fasion to create waves?
Can this be done while both pumps are connected to L1/2 using the YL2 splitter?


Sent from my iPhone using Tapatalk
 
Any pointers on how to program pumps in alternating fasion to create waves?
Can this be done while both pumps are connected to L1/2 using the YL2 splitter?


Sent from my iPhone using Tapatalk

Yes, easily do-able.
Check out this video:
https://www.youtube.com/embed/8eCp0KGWbf0

That's on my Reefer 450 (5ft tank) w/ a 6055(left) and a 6095(right) - using a 0.7/0.9 second timer.

StreamGroup #x
Mode: Permanent Opposite
Wave: Right Angle
MIN: 0.7
MAX: 0.9

Each pump is set to 0% & 100%.

07.18.2016-15.35.png
 
Last edited:
Setit up as recommended,but pumps now just stay off even though ghl control center shows the voltages alternating between the 2 pumps


Sent from my iPhone using Tapatalk
 
Setit up as recommended,but pumps now just stay off even though ghl control center shows the voltages alternating between the 2 pumps


Sent from my iPhone using Tapatalk

Make sure you assign the L# channels to the Stream Pump # - where# is the same as what you chose in your Stream Group.

In my case,
I'm using:
  • L1/L2 is the physical port on the ProfiLux
  • In 'System -> 0-10v Interface': L1 & L2 = Pump 1 & Pump 2
  • In 'Extras -> Stream Group 1': I assigned Pump 1 & Pump 2


07.18.2016-23.12.png


07.18.2016-23.06.png
 
Setit up as recommended,but pumps now just stay off even though ghl control center shows the voltages alternating between the 2 pumps


Sent from my iPhone using Tapatalk

Were you able to get the alternating wave going with the instructions provided?

<iframe width="640" height="360" src="https://www.youtube.com/embed/8eCp0KGWbf0" frameborder="0" allowfullscreen></iframe>
 
Back
Top