I'm wondering what is best for auto top off additions. I'm adding about 1 to 1 1/2 gallons a day of RO/DI due to evaporation and am considering buying a ATO system. Of course, I would like, hope, to make this purchase one time. I don't have enough of a calcium demand at this time that I need to do Kalc additions, adding two part is still sufficient. I am concerned that if I get a Kalc reactor as part of my ATO, I would be adding too much calcium. I can envision that I may get to the point that two part isn't enough and would end up adding Kalc as make up. Would be interested in some opinions. Thanks!
ATO... RO/DI or Kalkwasser?
- Thread starter tcollins
- Start date
jmait769
-CSHFLW
I’m using a <a href="http://www.tunze.com/149.html?&L=1&C=US&user_tunzeprod_pi1[predid]=-infoxunter036"target="_blank"> Tunze Osmolator</a> and a <a href="http://www.reeftek.com/Nilsen_Reactor.htm"target="_blank">ReefTek</a> Kalk reactor and have had zero problems. I used the Osmolator without the reactor for a while then added the stirrer later on. Can’t say enough about the Osmolator and how reliable it has been!!
HTH
Jay
HTH
Jay
jmait769
-CSHFLW
I have used this system for about a year and have also started to supplement calcium. The kalk keeps the alkalinity within parameters but calcium slides. I should say that I’m also using an AC jr which monitors the Ph and controls the stirring pump on the reactor. If the Ph gets above 8.3 then no stirring. So far this has only happened in the summer months but the water still runs thru the reactor. I like the Osmolator with the reactor because it only adds about a cup of RO/DI water at a time and I’m evaporating about 2 gallons a day.
HTH
Jay
HTH
Jay
Just a matter of testing Alk/CA and adjusting the top off accordingly. Thanks!
As an ATO is a neccesity, I'll get that first and then add the reactor like jmait769 did. Once there I'll supplement with the two part.
I've already had a percipitate incident using both Kalk and two part and don't want to do that again. Had to clean everything under the tank and haven't scrapped it all off some spots in the tank. Luckily it happened before my eyes and I was able to do a water change and didn't lose anything. I think my MG levels were to low.
As an ATO is a neccesity, I'll get that first and then add the reactor like jmait769 did. Once there I'll supplement with the two part.
I've already had a percipitate incident using both Kalk and two part and don't want to do that again. Had to clean everything under the tank and haven't scrapped it all off some spots in the tank. Luckily it happened before my eyes and I was able to do a water change and didn't lose anything. I think my MG levels were to low.
Every tank is a little different. Mine seems to use more alk than ca. I have to boost the alk every once in awhile. I use a Reef Fanatic dual level controller and an Aqualifter pump with a 44G Brute for a topoff container. It works out very well. The float switch is sensitive so it only adds a very small amount at a time, maybe a few oz. I evaporate ~ 2G in the Summer, 3G in the Winter.
jmait769
-CSHFLW
I wish I had the room to add a large RO/DI holding tank but for my next (larger) tank I dream of a separate fish room!!
The sensor for the Osmolator is located in my return area of the sump. So it evaps a certain amount and then gets replenished. If the area was larger then it would add more due to the amount evaporated for a given volume of water. I hope I’m saying that clearly!
Here is a shot of the sensor:
Jay
Thanks for the close up of the sensors, it was where I was planning on locating mine. I am also thinking it is where I'd put my ATO feed to the sump as the return pump would disperse it with good flow. When I start feeding through the reactor, it would also help cut down on the buildup on the other pumps in my sump.
I just dump an unregulated amount [roughly a pound] of kalk into my ro/di reservoir [32g] with the topoff pump for my sump situated on a grid halfway up from the bottom [down there the slurry collects]. I evaporate 1 g a day or more from my 54g, and after 'setting' the amounts for alk, cal, mg, in my tank manually by dosing, I am happy to report levels are proper and steady as set after a couple of weeks of this untidy quasi-machine running. With the addition of 10 more gallons of ro/di every week or so to the "Frankenreactor" it stirs the slurry up to combine with the ro/di and keep the level up. So far so good. [I also have a basement sump---but I am pretty sure you can do exactly what I have done in a 7g salt bucket with a lid and hole to let the hose out.
