Control modules
- Thread starter Bugger
- Start date
The control modules (CM466) are used to turn devices on and off. You can also use or direct connect boxes to do the same function if you don't want to use X10.
When there is a reliable and accurate enough Ca probe available we will add support to our controllers. Currently, there aren't any that are good enough for continous monitoring/control.
See the comparison table on our website for the list of differences between the controllers: http://www.neptunesys.com/comparison.htm.
Curt
When there is a reliable and accurate enough Ca probe available we will add support to our controllers. Currently, there aren't any that are good enough for continous monitoring/control.
See the comparison table on our website for the list of differences between the controllers: http://www.neptunesys.com/comparison.htm.
Curt
>What is RS232 serial port function?
The serial port allows the controller to be connected to your PC so that the datalogs, status, etc. can be imported into your PC through AquaNotes.
>Web Server?
Serves web pages so that you can see current status, datalogs, etc. through a standard internet browser.
>Telnet server?
Similar in function to the serial port, but instead uses the ethernet port for communication to the PC.
>RS485 serial port?
Multi-drop serial protocol. Single pair of wires can connect multiple controllers to one serial port on the PC.
>External moden support?
Allows an external modem to be connected to the controller for outgoing pages, dial-in communcation to a PC.
>Digital imputs and outputs?
Digital inputs are for connection to float switches, pressure transducers, water on the floor sensors. The controller can monitor these inputs, and then turn devices on/off or signal an alarm.
The outputs are used to create a very reliable hardwired control output. The outputs are wired to external relays which are used to turn on/off large pumps, lights, chillers, etc. These outputs are somewhat obsolete now that we have the DC4 and DC8 boxes.
Curt
The serial port allows the controller to be connected to your PC so that the datalogs, status, etc. can be imported into your PC through AquaNotes.
>Web Server?
Serves web pages so that you can see current status, datalogs, etc. through a standard internet browser.
>Telnet server?
Similar in function to the serial port, but instead uses the ethernet port for communication to the PC.
>RS485 serial port?
Multi-drop serial protocol. Single pair of wires can connect multiple controllers to one serial port on the PC.
>External moden support?
Allows an external modem to be connected to the controller for outgoing pages, dial-in communcation to a PC.
>Digital imputs and outputs?
Digital inputs are for connection to float switches, pressure transducers, water on the floor sensors. The controller can monitor these inputs, and then turn devices on/off or signal an alarm.
The outputs are used to create a very reliable hardwired control output. The outputs are wired to external relays which are used to turn on/off large pumps, lights, chillers, etc. These outputs are somewhat obsolete now that we have the DC4 and DC8 boxes.
Curt
RS485 would be used if you have many AquaControllerPros that you would like to connect to a single PC. The PC would only need a one RS485 serial port.
A pressure transducer monitor's whether or not there is a certain amount in water pressure in a return line. With it you can monitor whether or not there was a pump failure.
Digital inputs are a way to get information from switches, etc. into the controller. It has nothing to do with reliability.
The digital outputs and the DC4/DC8 modules have about the same level of high reliability for control. X10 control is less reliable.
Curt
A pressure transducer monitor's whether or not there is a certain amount in water pressure in a return line. With it you can monitor whether or not there was a pump failure.
Digital inputs are a way to get information from switches, etc. into the controller. It has nothing to do with reliability.
The digital outputs and the DC4/DC8 modules have about the same level of high reliability for control. X10 control is less reliable.
Curt
Yes, the 3Pro has two power connectors and one is design for backup power.
The Aqua2 and Pro have 9V battery for backup power so that the controller remains working for 4 to 6 hours after a power failure. The 9V battery clip on these controllers could be hooked to 9V AC adapter that is plugged into a UPS and work the same as the 3 Pro. It is just not as elegant.
Curt
The Aqua2 and Pro have 9V battery for backup power so that the controller remains working for 4 to 6 hours after a power failure. The 9V battery clip on these controllers could be hooked to 9V AC adapter that is plugged into a UPS and work the same as the 3 Pro. It is just not as elegant.
Curt
Bugger
New member
UPS relay for the entire system would be a great idea for a future model. I know it seems easy to make for your company to make but most regular people don't have a clue how to put somthing like that together.
Anyways...
Curt I want to buy one right now but I still don't underrstand how to control things, Are the Modules nessary for heaters and lights.
Or maybe a better question is where do I plug the heaters and lights into?
Anyways...
Curt I want to buy one right now but I still don't underrstand how to control things, Are the Modules nessary for heaters and lights.
Or maybe a better question is where do I plug the heaters and lights into?
There are 2 options for control - X10 or our Direct Connect Boxes. For new installations I recommend our Direct Connect boxes; the DC8 is most economical from a price per outlet standpoint. The devices you wish to control simply plug into a Direct Connect outlet, and the AquaController is configured to turn that outlet on and off at the appropriate times.
Curt
Curt
