DIY overflow box

[SFish]

Looking into making an overflow box. I'm looking to run 500gph. My DT is a 75gal. I have 1" pvc on the return line. The tank has trim on it. From the outside the trim is 1 3/4" wide. Because of my 3D wall the overflow box needs to be the size of what I have now roughly. What I have now is 7 1/4" L x 3" W x 5/8" on the outside of the box. My guess is the box wouldn't be big enough for PVC 90's to fit inside so I would need an internal and external box. I was thinking of using two 4 sided boxes and using a bulkhead to hold them together. Because of space I thinking to put a herbie style overflow.

The box I have now from a HOB overflow that is made to fit in the 3D wall



The 3D wall







You can see the wall will be bonded to the back and side of the tank.

 

[SFish]

Ok so questions

1) what size bulkhead should I use to connect the internal and external box together?

2) would I have to use 1 1/2" PVC to go from the external box to the sump then?

3) would I need to use two 90's to make one of these or do I not need that U shaped pipe?



4) will a bulkhead be ok supporting the weight of the boxes?

5) about how big do you think I would have to make the external box?

6) how far from the top of the trim should the internal box be?

7) about where should the hole be that connects the two boxes in relation to the internal box? Do I want the top of the hole just below the teeth of the overflow?

 

[SFish]

I would just drill the box I have but that tab on the back sticks out so the box would not go flat against the glass.

 

[SFish]

No one with any advice or links to look at? What do people do when they install an internal overflow?

 

[DeepSeaReefer94]

I built my internal overflows on my tank out of 1/4" blue acrylic. I wanted a tank that could be viewed from both sides. I'll try to remember to take some pics when I get home. But other than that I'm not much help to you.

Sent from my SAMSUNG-SM-G870A using Tapatalk

 

[EvenFurther]

This is what I'm doing right now on my 24" x 18" 37 gallon. I'm attaching a 9" x 4" x 6.5" glass box to the exterior, and a Modular Marine low profile acrylic internal box. For aesthetics, the internal box was sized to completely cover the outer silicone seams and outer box. The outer box will be set up with a herbie drain. The internal is a 11" low profile design which really helps on this small tank.

 

[DeepSeaReefer94]

I built my internal overflows on my tank out of 1/4" blue acrylic. I wanted a tank that could be viewed from both sides. I'll try to remember to take some pics when I get home. But other than that I'm not much help to you.

Sent from my SAMSUNG-SM-G870A using Tapatalk

this is my internal overflows the top of the pvc is a T with a cap on the top that has a 3/16" hole drilled in it and a 90 that is pointed down. It's very quiet. You don't have the waterfall noise that most tanks have. In fact I can barely hear it with the lid open on my aquarium.

Sent from my SAMSUNG-SM-G870A using Tapatalk

 

[SFish]

I built my internal overflows on my tank out of 1/4" blue acrylic. I wanted a tank that could be viewed from both sides. I'll try to remember to take some pics when I get home. But other than that I'm not much help to you.

Sent from my SAMSUNG-SM-G870A using Tapatalk

Thanks

 

[SFish]

This is what I'm doing right now on my 24" x 18" 37 gallon. I'm attaching a 9" x 4" x 6.5" glass box to the exterior, and a Modular Marine low profile acrylic internal box. For aesthetics, the internal box was sized to completely cover the outer silicone seams and outer box. The outer box will be set up with a herbie drain. The internal is a 11" low profile design which really helps on this small tank.

How big is the bulkhead to go from the internal to the external box?

 

[SFish]

I been looking at Ghost overflows trying to get an idea of how they are put together to give me something to kind a go off of.

 

[EvenFurther]

I'm not using a bulkhead, there is 2, 1.75" holes. Just finished drilling the holes.

 

[SFish]

Oh so your bonding the outside box to the tank on your set up. You hole size is in between a 1 and 1 1/4" bulkhead hole.

 

[EvenFurther]

Yep using RTV108 for the outer glass box. The 1.75" hole is what Lifegard Aquatics specifies for their 1" bulkhead, which is why I had that size bit.

 

[SFish]

Thanks

 

[ca1ore]

When I did this some years ago, I used an acrylic inside weir box and an external glass scupper box. I'd suggest using a bulkhead to help hold the internal box as silicone doesn't bond plastic very well and you don't want to accidentally knock it off. When I did mine, I used a 1 1/2" bulkhead. I also drilled the external glass pieces for the drains before assembly and I just did a 4 piece box siliconed to the back of the tank.

 

[SFish]

Thanks

Yeah I'm going to use a bulk head to hold both boxes on. The same way a ghost overflow does. From what I can tell I think I can get away with 1 1/4". For the emergency I read a 1" pipe can handle 330gph and I'm going to be running 500gph so 1 1/4" should be fine as far as I can tell. How big did you have to make your outside box? Is the bulkhead and silicone the only thing holding it on?

 

[EvenFurther]

On a ghost overflow, the bulkhead is what holds both the inner/outer box to the tank. The set up uses 2 gaskets per BH, one on each side of the tank glass.

 

[SFish]

On a ghost overflow, the bulkhead is what holds both the inner/outer box to the tank. The set up uses 2 gaskets per BH, one on each side of the tank glass.

Yes
This is the design i'm shooting for. Not sure but it looks like the emergency drain goes to about the top of the bulkhead.

 

[CK00020]

Go Pack

 

[SFish]

Huh?