LED Recommendation Thread

brassmonkyballs said:
Good info you're adding here Lipitor. I made a Royal Blue only supplement bar for a friend who added it over his 150 with his T5s and it looks very nice and he's raving to anyone that will listen. So its a good point on that combo of LEDs with T5's.

The tricky part of the XMLs is that to get the most out of them you really have to up the current. True you can get more than an XPG at the same current but the cost difference doesn't justify it unless you push them....and then they are so bright I wouldn't know what to do with them. I know someone is just finishing up a build with some of them at 2000ma so it will be interesting to get his thoughts. He's actually using XPGs and XPE RBs as well.
Click to expand...

From what I understand however occupied run the XMLwith a lower current you can get more lumens with less energy add more life, correct? That is why I am looking for CREE XM-L LEDs
 
Yeah thats why I have been asking so many questions. I think I will go with no optics then and try to keep it a little closer to the tank. I may just drill the sink myself just as you said, seems easy and maybe with the little money I save on the sink I can add a couple more LEDs to my order :D
 
bif24701 said:
From what I understand however occupied run the XMLwith a lower current you can get more lumens with less energy add more life, correct? That is why I am looking for CREE XM-L LEDs
Click to expand...

I believe LEDsupply.com has them. I'm not sure if I said that in this thread yet, so sorry if I'm repeating myself and being rude. That isn't my intention at all.

But I couldn't see a better DIY LED setup then with cree's and the XM-L is just really awesome.

If you build a fixture, make sure to post pics here, I would be more than eager to see! :thumbsup:
 
bif24701 said:
From what I understand however occupied run the XMLwith a lower current you can get more lumens with less energy add more life, correct? That is why I am looking for CREE XM-L LEDs
Click to expand...

Yes but they are $10 vs $5 for the XPG. That was my point in not being able to justify them. I'm not saying don't use them just for the cost difference they are not for me unless I ran them up in the 2000ma range. I'm not worried about life either because LEDs are rated for a very long life already. Keeping them cool is the key.
 
LFS says I need "moonlight" LED

LFS says I need "moonlight" LED

Hey guys,

I have been reading for about two days and come to the assumption to once again, ask the experts...

Current Set up =
29 Gallon Tank - Clownfish & anemone only
30L x 12-1/2" W x 20 T
2 (ea) T8 "white light" bulbs
2(ea) T5 "blue light" bulbs

LFS says I need a LED Moonlight strip too.... SO here is the question, my current set up is part of the hood so I don't really have anywhere to put another LED light Fixture. Please guys, can you point me in the right direction? I was under the assumption my current lighting set up was a good set up, but it does lack the luster of the color the LFS LED lighting provided.

Can anyone give me a solution that keeps my current setup, but provides a good "moonlight" alternative?


Scott70454
 
Can someone recommend a link for "LED's for dummies"? I know NOTHING about them except I may want to put them over my 300g. :)
 
Hey BMB. Got any actual power consumption reading for your build? There was a thread awhile back stating that some DIY rigs were using much more power that they should be. A friend of mine as a 24 LED setup using all 3 watt crees and his rig is pulling 125 watts of juice. I was just wondering if you experienced anything like this. Thanks.
 
My LED journey is as follows:

I have my only current tank in my office so while I like the look of a fixture suspended over a tank sans hood I don't want people throwing stuff in the tank when no one is looking so I decided a hood is a must. I used to have a 3x48" VHO set-up which was fine but they got hot and raised my tank temp somewhat even with a fan and I hated having to swap out the bulbs when they reached their EOL. I added a Reef Brite blue 48" strip for a little actinic supplementation and loved the blue highlights it added so much I decided to go all LED and eventually added another 50white/50blue model along with a couple of big 36w 5500k PAR38's to add a little yellow balance to the decided blue look.

Recently I added a new Reef Brite XHO model 50/50 with the goal of eliminating the PAR38's but I found they actually work even better together because the shimmer coming off the PAR38's is nothing short of MH-like and the yellow cast give a more balanced look IMHO. The only problem I had was mounting the three RB's in my hood made it difficult to do any work in the tank w/o removing the hood. I came up with a solution that involved using the 3-way RB mount sliding on some aluminum T-Track held in place with some quick release cam locks so I can instantly slide the whole RB set-up back into the hood for more clearance when I want to and then slide it forward when done. It works so well in fact that I leave the lights far more forward than I had ever considered mounting them because the light looks better more toward the front angled back into the tank.

I really like having four distinct lights hooked up to my Neptune controller too. The blues are the first to come on (and last to go off), along with a fan to cool the hood. Then an hour later the standard grade 50/50's come on followed by the XHO's a little later and then finally the PAR's come on for a midday sun effect for about 5 hours. Then they all go off in reverse order.

I guess the whole point to my post is that how you start setting up your lights may not be how you end up and there is nothing wrong with building a component at a time and flesh it all out to your own taste. I couldn't be happier with how my lights all turned out but it did take a while to getting them where I wanted them to be.
 
Last edited:
Thanks bigkahuna, nice little review!

This is quite similar to my situation. I'm getting two AIs that I just ordered today and will be adding depending on how I like the look of two over a 75 gallon. Lets just say I'm really excited and am very anxious for them to get to my house! It's really an advantage over traditional forms of lighting that you can add modules and save money so easily.
 
reefermad619 said:
Hey BMB. Got any actual power consumption reading for your build? There was a thread awhile back stating that some DIY rigs were using much more power that they should be. A friend of mine as a 24 LED setup using all 3 watt crees and his rig is pulling 125 watts of juice. I was just wondering if you experienced anything like this. Thanks.
Click to expand...

no i haven't measured it. What did he use for the measurement? Couple thoughts...assuming he used 2 Meanwell ELN 60-48 drivers....each one is 60 watts...2 X 60 = 120W so if he used all of it then yeah its possible...the other thing is do you know what Cree's he is using? are they XRE or XPG/XPE?

You have to take the 3 watt rating with a little grain of salt sometimes. If a Cree XRE were running at 3.5V and pushed to 1.3A thats really 4.55 watts, if that were what he was running at then 24x4.55=109 watts. SInce we don't know which Cree 3w he is using and what his parameters are its hard to say whats going on...but you can see theoretically its possible. But take that same rig and run it off one driver with 2 parallel strings of 12 at 700ma and you just halved the power.....

It would be interesting if he could measure the voltage and current of each string at the LEDs and compare that to whatever he used to measure the total...probably a kill-a-watt or something.

I'm using XPGs and XPEs and they tend to run about 3.1V at about 1A so around 3W times 74 is about 220W theoretically.
 
I was wondering what the correlation between PAR and Lux. I assume the more lux, the more par, but I'm not sure.

Also, have there been any reports of those aluminum U-channel's used in place of heatsinks causing heat problems? I have access to a bunch of scrap sheets of aluminum, and was wondering if I could just cut strips and bend them to make my own U channels. If I do, what thickness is ideal, and how long should the fins be?

One more, I plan on using the ELN-60-48D and running 13 XM-L's in a series, and plan to dim with my Apex. Do I still use the 10v AC to DC power adapter to dial in my driver, or does the Apex take care of it?

Thanks!
 
Response in Blue

fns said:
I was wondering what the correlation between PAR and Lux. I assume the more lux, the more par, but I'm not sure.
YES and NO. The NO part:- Lumens are based on eyes but our eyes are not linear reacting to the light energy in different color(spectrum) even though the light energy may be the same. To better indicate what human beings feel visually, we use a formula in the Lux meter to express them what we human beings think the brightness is. Now that goes for PAR too, but this time they are formulated to be used for plants' photosynthesis. So the reading is designed to reflect better what the plants reaction is. The YES part:- Unless the light is very tight in the spectrum like LED, most commercial lighting technologies are a mix of spectrum and thus both the human eyes react to some of them while the chlorophyll of the plant react to some of them too, even though not necessarily the same. So in real frequently we find that higher Lumens bulb also yield higher PAR. Problem becomes even more complex-the meter you use. A lot of PAR meters also register green significantly in their readings but as scientists will tell you they are not of much use by chlorophyll in plants(hence the Zoa in coral), so the PAR value for coral growth is also an rough collectively assumption(not really exact) but yet yielding close results to what we expect them to be.

Also, have there been any reports of those aluminum U-channel's used in place of heatsinks causing heat problems? I have access to a bunch of scrap sheets of aluminum, and was wondering if I could just cut strips and bend them to make my own U channels. If I do, what thickness is ideal, and how long should the fins be? To calculate the proper surface area you need to know the total power of your LEDs, the heat co-efficient of the heat sink material and ...... I would just try to over do it than doing the math. If it's an passive heat sink design, you should not have the fins too tall as it will create channeling. The thickness of the aluminum base is to help the initial heat sinking when the diode fires up. There is a lot of heat energy when the LED is fired up, so you want thicker base over thinner base to quickly transfer all the heat energy away from a focal point and then let the fins to re-transfer than to the air. I myself would not trust an U channel thing from Home Depot as a heat sink unless you are using a fan to make it an active heat sink.

One more, I plan on using the ELN-60-48D and running 13 XM-L's in a series, and plan to dim with my Apex. Do I still use the 10v AC to DC power adapter to dial in my driver, or does the Apex take care of it?

Thanks!
Click to expand...
 
Last edited:
Were can you get CREE XM-L LEDs? I googled it but got nothing but forum threads and stores that have CREEs but not XM-Ls. Please help, lol
 
Goggled clay-boa and got a dead link,

This is the fifth time I've posted the question no real link, or shop. Please help....
 
You must log in or register to reply here.

Similar threads

K
Radion time help. (Long post)
Replies
2
Views
127
kj swans
K
newsalt
Aqua Illumination SOL Blue problem
Replies
2
Views
144
oreo57
oreo57
J
LED fixture lighting help (replacing old T5 HO)
Replies
5
Views
733
griss
griss
sickman
Juwel Lido 200 - really reef tank ready all in one? Really Really?
2
Replies
39
Views
871
Reefing102
Reefing102
C
Maxspect jump led issue
Replies
0
Views
1K
Cruzersmith
C
Back
Top