New 325G In-Wall Project
- Thread starter LIReefer
- Start date
LittleBlueGT
New member
Looks awesome! As far as flow goes consider using the OM HD 4-way unit. With a 2 inch inlet and 1.5 inch outlets it can flow a lot more than an 8-way. I believe that 4 ways is enough to have random current in the tank. I own a hammerhead pump. I also own a HD 4-way. You can check out my build here. If I were you I would get a good deal on a SEQ 1000 series pump vs. a reeflo. They can be gotten at custom aquatics for a decent price, and I think they are of better build quality. I broke the volute on my Hammerhead, and I have heard of others that have too.
jimmy n
Active member
Just a piece of advice on the external overflow.
Your acryllic looks very thick, and may bow very little. But the slightest bow will cause the corners of the external overflow to bow out and create potential leaks.
I know this because I made this mistake in the past and had to trash my 140 with external overflows. My overflows, in contrast were higher on the tank with thinner acryllic so you may not experience this problem.
Jim
Your acryllic looks very thick, and may bow very little. But the slightest bow will cause the corners of the external overflow to bow out and create potential leaks.
I know this because I made this mistake in the past and had to trash my 140 with external overflows. My overflows, in contrast were higher on the tank with thinner acryllic so you may not experience this problem.
Jim
javajaws
Premium Member
littlesilvermax said:
Ditto on the Seq 1000 recommendation. I just got mine last week and it's a monster (28 lbs!). Thats some serious material they made the volute out of, not at all like the reeflo series. Also comes with all stainless hardware (not sure if the reeflo's do). Now if my danged tank and OM 4-way would get here so I can hook that bad boy up...
LIReefer
Member
Almost Home
Almost Home
Here are the last shots before delivery:
Overflow Screen in place
All trimmed and ready to be crated!
In the crate.....Come to papa!
If you want a custom tank built - this is the place to go http://www.envisionacrylics.com/
Ed
Almost Home
Here are the last shots before delivery:
Overflow Screen in place
All trimmed and ready to be crated!
In the crate.....Come to papa!
If you want a custom tank built - this is the place to go http://www.envisionacrylics.com/
Ed
SaltFishMD
Premium Member
any updates on this tank? did you have any bowing problems? how much did the tank cost?
LIReefer
Member
Update on Progress
Update on Progress
Sorry it took so long but I've been very busy!! Here are some of the latest pics on the progress. So far the basement is framed as well as the fish room. The tank stand is built and the tank is sitting in place. In addition a 220v 60amp sub panel is installed to feed the equipment room.
Stand Construction:
Rough Opening:
Tank in place:
http://reefcentral.com/gallery/data/500/7997tank_in_opening.jpg
Rear of tank inside room:
Start of sub panel wiring:
There still is a lot more to do!
Ed
Update on Progress
Sorry it took so long but I've been very busy!! Here are some of the latest pics on the progress. So far the basement is framed as well as the fish room. The tank stand is built and the tank is sitting in place. In addition a 220v 60amp sub panel is installed to feed the equipment room.
Stand Construction:
Rough Opening:
Tank in place:
http://reefcentral.com/gallery/data/500/7997tank_in_opening.jpg
Rear of tank inside room:
Start of sub panel wiring:
There still is a lot more to do!
Ed
Last edited:
A Reef Scene
New member
That is a great looking set up.
