pics of temp system

NaClH2Opgh

New member
Here are some pics of my temp system up and running. It's around 110 gallon with a 25 gallon sump. There is a probably a total of 120 gallons of water. I am using (2) lumatek dimmable ballast (250/250HQI/400/superlumen), (2) Lumenbright wide reflectors and (2) 250w se Reeflux 20k bulbs. I also started running Warner Eco Bak pellets last night. I am going to see if these can replace my vodka dosing regimen.

628811bf.jpg


sump with the 250 Extreme skimmer (from Rays bargain bin)

11bc034e.jpg


Vertex Zeo reactor (from Rays bargain bin) running 500ml of Warner Eco bak
I plumbed the output of the reactor to empty next to the skimmer pumps



8fb160d1.jpg
 
Some pics of the coral:

1a047fae.jpg


3 or my four clams. These 3 are all maxima:

f5cc8685.jpg


pic of my purple monti that I accidentally fragged then almost killed when I put it into the temp system. It is finally coming back:

7da24f4b.jpg
 
Nice, real pictures this time too!
Thanks, I figured I should post real pics since I still can't get a pic of the spotted tang. I actually was worried and kept checking the floor around the tank. I hadn't seen him since I put him in but spotted him yesterday before the lights went out. He always stays near the bottom of the tank.
 
Here is a little better pic of my Dersa clam that I picked up from Brett previously. I love the colors in this one. There is also a better pic of my sunset monti in back of it. All these pics were taken with my Droid phone.

e49cba0c.jpg


I also had issues with putting the Warner Eco Bac Pellets in the Zeo reactor. The holes in the plates on the top and bottom of the reactor were just big enough for the pellets to fit through. I really didn't want to use a sponge that would get clogged easily over time. I purchased this at the craft store and cut two pieces out to fit over the plates and now the reactor is perfect for the pellets. When I go to refill it, all I need to do is lift the plunger cylinder out instead of lifting the entire reactor out of the sump.

14f45494.jpg
 
I figured I would post some pics of the reason I can't start on my 225 gallon upgrade yet. 1) we are just finishing up painting the room where it is going:

22a9fefe.jpg


2) The main reason. I am gutting our 2nd floor bathroom down to the studs/joists and then blowing out the wall and expanding it into our bedroom. I can't even think about starting my stand for the tank until I am laying tile in the bathroom...lol


043f1cbc.jpg


ba395926.jpg


I also have a video I am uploading with 90% of the demo done. I'll post when it's ready.
 
OK here is the video of what the bathroom looks like now. The section the left into the bedroom will only go to where I have the plaster taken down. In the bedroom there will be a small area to put my wife's vanity. To the right inside the bathroom I took out some 2X4's and put a header board in so I can make a built in cabinet about 5 foot high.

<object width="480" height="385"><param name="movie" value="http://www.youtube.com/v/PKOd92cfNnc?fs=1&hl=en_US"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/PKOd92cfNnc?fs=1&hl=en_US" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="480" height="385"></embed></object>
 
I got this one at Elmer's after the meeting. It was only $34.99. It looks green and maybe orange. Hard to tell, I'm hoping it will color up. If not just green I guess., we'll see. It was hard to get a clear pic. It is on the bottom and at the back. I kept getting too much light. I don't have any actinics on the tank so it's the best I can get now.

f2330d3a.jpg
 
Back
Top