wire sheathing tunze stream 6100

[Bladez]

Mr. Vitko

I purchased 4x 6100's in Jan 2006.

This weekend I removed one of them form my tank for cleaning and the black sheathing protecting the smaller wires running into the back of the pump split open. It is right at the back of the pump where most of the wire flexing occurs. I put the unit back into the tank and it is operating fine but I just wanted to get your input as to repair options etc...

Will the windings be damaged if I continue to operate the pump like this?

The sheathing running into my other 3 pumps is brittle also so I may need a preventative plan to prevent this in the future.

I haven't taken any pictures yet but I will if needed.

Thanks in advance for your help and your advice.

Bladez

 

[rvitko]

In this case we would recommend replacing the motor, the 6100.015 motor is no longer available so instead you would be eligible for a discounted upgrade to a 6105. The risk of water entering the motor is quite slim, the outer insulation is stripped about 1/4" under the resin and the 5 individual wires connect to there respective components so this creates a seal to prevent water from entering. The main risk is that by capillary action water will wick down to the driver and the exposed individual wires are much more easily damaged. This cable has a cloth liner that acts like a wick to carry water back to the driver box.

 

[johnwonus]

I have the comline protein skimmer with the same problem. Would you have the same advice? Could I put silicone sealer around the wires?

 

[Bladez]

There was no suggested solution to this issue other than replacement. I was informed, however, that TUNZE designs their products to have a useful life of around 5 years. My pumps have been in service for around 5 years.

I have the comline protein skimmer with the same problem. Would you have the same advice? Could I put silicone sealer around the wires?

 

[rvitko]

Johnwonus, I would replace the motor in this case as the motor is likely 115V or 230V unless it is a very old 3140 or 240 skimmer which used a DC motor, the risk of high voltage AC is too great to take a chance on.

 

[johnwonus]

Thanks for the advice. I will replace it right away.

 

[xinumaster]

Wires sheathing on two of my tunzes (6200 and 6100) too. Tried to fixed it by inserting a shrink tube and glued to body using flex plumber glue the to cover the expose wires. It worked for a few weeks, but pumps stop working again.

 

[Bladez]

This is quite frustrating.... It is like a gas line failing on a Lamborghini!!!

Wires sheathing on two of my tunzes (6200 and 6100) too. Tried to fixed it by inserting a shrink tube and glued to body using flex plumber glue the to cover the expose wires. It worked for a few weeks, but pumps stop working again.

 

[rvitko]

I am sorry, but this motor was discontinued late last year and they were all sold out by February. It was a $110 part, instead you will get an upgrade to the latest model pump which is smaller, stronger and moves in all direction for $180, I don't really see the need for a long thread of what ifs and complaints we are more than happy to resolve the issue in what I think is a very fair manner.

 

[Bladez]

Roger,

Sorry for causing a stink (I'll refrain)... I am interested in a replacement (ASAP) but I don't have the $$ right at this time.

I do appreciate your offer and prompt and professional CS!
:fish1:

I am sorry, but this motor was discontinued late last year and they were all sold out by February. It was a $110 part, instead you will get an upgrade to the latest model pump which is smaller, stronger and moves in all direction for $180, I don't really see the need for a long thread of what ifs and complaints we are more than happy to resolve the issue in what I think is a very fair manner.

 

[rvitko]

Thanks, no worries, when you are ready, let me know.