RedEDGE2k1
Member
Redneck 90° clamps 
The side shelves
Screwed/glued to the top section
The side shelves
Screwed/glued to the top section
Custom Cabinet for 90g Reef (Build Thread)
- Thread starter RedEDGE2k1
- Start date
RedEDGE2k1
Member
My blue-eyed blonde helper
Installing the shelves
Trim, to hide the cut edge of the plywood shelf
1/4" pine stop trim around the tank display cutout. I positioned the cutout/trim to cover the 1/2" silicone smears at each side of the tank. It worked out well -- now only only clean glass is visible through the front panel.
Progress photo, as of Friday night, 10/12/07
I have more progress to show since that last picture, I just haven't had time to download the pics from my camera and get them on Photobucket (great picture host, by the way). All that's left on the build is crown moulding, hinging & trimming the access panel, and final wood putty/sanding. Hopefully I can finish the build tonight, and start sanding/priming tomorrow night.
Installing the shelves
Trim, to hide the cut edge of the plywood shelf
1/4" pine stop trim around the tank display cutout. I positioned the cutout/trim to cover the 1/2" silicone smears at each side of the tank. It worked out well -- now only only clean glass is visible through the front panel.
Progress photo, as of Friday night, 10/12/07
I have more progress to show since that last picture, I just haven't had time to download the pics from my camera and get them on Photobucket (great picture host, by the way). All that's left on the build is crown moulding, hinging & trimming the access panel, and final wood putty/sanding. Hopefully I can finish the build tonight, and start sanding/priming tomorrow night.
Last edited:
This was obviously going to be a fantastic built from the very beginning and I am looking forward to each installment you post up. I have a rather general question for the woody heads (no pun intended) though; how does the 1x2 poplar trim glued up to the more stable plywood react to humidity? Wouldn't it try to pull out? If there is one thing I learned from Norm, that is not to lock two different material together and pay attention to the grain direction. I see quite a bit cross grained plywood in your built but I presume it wouldn't matter as much since it is plywood which is more stable than non-engineered wood. Any tips, hints?
Thanks again sharing this great adventure with us.
Thanks again sharing this great adventure with us.
RedEDGE2k1
Member
Thanks!
To my knowledge, it might be a concern if the wood were left unfinished; but with a couple coats of primer and a couple coats of paint, the humidity resulting from tank evaporation, particularly outside the "hood" area, isn't worth worrying about. If it were, I'd be more worried about our drywall and hardwood floors than the tank cabinet.
Also, the 1x2 poplar is glued to the plywood end-to-end. I couldn't pull it off with a hammer, even if I wanted to.
cannarella
New member
RuhiA, good question. Where you have to worry about cross grain problems is in gluing something against the grain in solid stock. The wider the solid stock the worse it could be. If are under 2-4 inches on the stock that you are gluing againt the grain on there is no worry. Now you can glue with the grain with no problems. Since plywood is a bunch of glued layers perpendicular to each other there is no worry about movement. Plywood is quite stable. It may swell a little, but not enough to cause one of his joints to fail.
BonsaiNut
Premium Member
Interesting thread. Couple quick comments:
1) Forget the bar in between the two doors at the base of the stand - you will hate yourself forever if that is constantly in your way. Instead, afix the bar to one of the two doors so it swings out of the way when you open or close the door. You get the same result without a permanent bar in your way.
2) Next time you are doing cut-outs in plywood consider a router and a drywall straight-edge. Perfectly straight and smooth cuts without splintered edges. Just need to finish the corners with jig saw, but if you use the right router bit you are talking 1/4" or less of touch-up per corner.
1) Forget the bar in between the two doors at the base of the stand - you will hate yourself forever if that is constantly in your way. Instead, afix the bar to one of the two doors so it swings out of the way when you open or close the door. You get the same result without a permanent bar in your way.
2) Next time you are doing cut-outs in plywood consider a router and a drywall straight-edge. Perfectly straight and smooth cuts without splintered edges. Just need to finish the corners with jig saw, but if you use the right router bit you are talking 1/4" or less of touch-up per corner.
RedEDGE2k1
Member
The bar between the doors isn't attached to anything, it will be held in place by friction only....so it's completely removable. I didn't want to attach it to the cabinet doors because in order to keep the doors swingy nicely, I couldn't put enough friction between the bar and the front panel of the cabinet. I'd have to leave a little bit of room for it to move, and this would let light shine through from the refugium light.
The cabinet doors are approximtely 21x22" each, and the bar between is only 1", so I don't think it will get in the way. If I had to bet, I'm guessing I'll probably very rarely remove the bar, if at all. Of course, after the sump and everything is in place.
I finished the crown moulding last night....wow, what a pain in the butt that was. Last time I played with crown, I used a handsaw and a plastic miter box, and had near perfect results. This time I used an electric compound miter saw and a plywood jig, and had the most miserable time. After 3hrs, I had crown moulding, but the joints were sloppy and will need to be packed with wood filler and sanded a couple rounds. Kudos to those of you who install crown for a living.
The cabinet is not complete, with the exception of hinging the access panel above the tank. I have two different sets of hinges, I'm going to build a mock-up tonight and see if (hopefully) one of them will work.
Pictures to follow.
RedEDGE2k1
Member
You're telling me....I have a newfound respect for furniture craftsmen in the pre-electron days.
The only tools needed for this job, at least the way I like to do things, are as follows:
Rotary saw w/ homemade straightedge jig
Drill and drill bits/screw driver
Hack saw & miter box
Hammer & nail set
Power orbital sander (not technically "required"....but lets be real)
Thats it for me...it would have been nice to have a nail gun for the trim work, and a router for the cabinet door openings, and clamps of all different sizes/shapes, but hey....I did just fine without all that stuff. I did drop $100 on a jig saw, which I regret, because in the end a $10 hack saw would have accomplished the same thing (cleaning up the edges @ cabinet door openings).
BonsaiNut
Premium Member
Just making suggestions for you to help your project "be all it can be"
The fewer loose pieces you have, the better, in my opinion. Something held in place by friction will last as long as the wood (1) dries or (2) expands, which is highly likely given temp and humidity around an aquarium.Here's a build on the last idea. Afix the bar to the back of one of the doors. Then at the TOP and the BOTTOM of the opening (where the bar would fit when the door is closed) place a small piece of backer board (thin wood piece) that sticks up from the bottom of the frame about 1/2" and down from the top of the frame 1/2". Perfectly light-proof and you only have a small nub of wood to work around instead of a bar.
I always justify one new tool per project
Now I can look at my tools and say - oh, there's the hammer drill I got for the security fence in the pool deck; or there's the nail gun I got for the bar cabinets It's like personal history and functionality all built into one
cannarella
New member
Only one new tool per project??? I mean something this big should deserve at least 2-3 new tools. I mean if you hang a shelf you deserve at least a jack hammer or demo saw...
cannarella
New member
Better yet, cut the bulk out with skill saw leaving 1/8" to clean up with the router. Much less dust and can be done in one shot. Remember on inside routs like an opening go clock wise and outside routs like a table top go counter clock wise. This will keep the router against the guide and prevent it from running away from you.
Let us know how the hinge tests for the opening turn out.
RumLad
New member
http://www.reefcentral.com/forums/showthread.php?s=&postid=10951794#post10951794
Jeez, why didn't I think of that? :smokin: :mixed: :smokin:
RedEDGE2k1
Member
I finally found some time to post pictures from the build from this past weekend. The build is now complete, with the exception of hinging the access panel door.
The fluted column cap & base. I bought these at Home Depot, they were originally much larger than what you see here. I cut them down to size with a miter saw, to match what I needed.
The fluted column trim, also from Home Depot, went in between. It hides the exposed plywood cut edge at the corner of the cabinet. I glued these in place and also used 3 or 4 finish nails to hold them in place until the glue dries. Later I'll fill in all these little holes with wood filler, then sand smooth.
Pre-primed wood base, again from Home Depot. Cuts were made on a compound miter saw.
The fluted column cap & base. I bought these at Home Depot, they were originally much larger than what you see here. I cut them down to size with a miter saw, to match what I needed.
The fluted column trim, also from Home Depot, went in between. It hides the exposed plywood cut edge at the corner of the cabinet. I glued these in place and also used 3 or 4 finish nails to hold them in place until the glue dries. Later I'll fill in all these little holes with wood filler, then sand smooth.
Pre-primed wood base, again from Home Depot. Cuts were made on a compound miter saw.
cannarella
New member
Looking good as usual. Did they let you buy 1' of that moulding for the top and bottom of the column?
RedEDGE2k1
Member
As mentioned earlier in the thread, I bought a jig saw to cut out the cabinet door openings. I tried running the jig saw along a straight edge while making the cuts, but it didn't work because of the flexible blade on the saw....the saw tends to follow the blade, wherever/whenever it chooses to bend/stray from the cut line. And once it leaves the cut line, there's no going back and retrying the cut, because the blade will still follow the bad cut (least resistance). Check out the resulting cut:
To fix this, I used my rotary saw, with the blade depth lever completely loose, allowing the blade to move up & down freely. I positioned the saw blade where it needed to be, with the saw base against a straight edge, and slowly lowered the blade down and into the plywood. Once all the way seated, I pushed the saw along the straight edge. The corners were finished with the jig saw, handheld, by eye. Here's the result, a much straighter cut:
At this point I packed all the screw/nail holes and wood imperfections with Elmer's wood filler, to be sanded smooth later.
The following day I began the crown molding. Wow...what a pain in the butt. I had three 8' lengths of pre-primed pine crown from Home Depot, and ended up going through all of it before getting things right. The miter cut angles have to be perfect, otherwise the pieces will never line up in the same plane with each other, and you get a resulting bad joint that must be packed with wood filler and sanded. This removes the clean corner of the joint, and leaves a slight rounded look, but hey....whatever. I was just glad to be finished with this stage of the build.
I covered the vertical plywood edge of the left/right shelf sections with this simple pine trim from Home Depot. It has very subtle fluting, to distinguish it from the shelf trim, while helping it match the fully fluted trim columns on the bottom section. I think it ties the two trim selections together nicely.
The top section, almost complete. Just needs the access panel to be installed.
The two sections together, thus far.
The custom cabinet doors arrived at my office today from www.advantagecabinetdoors.com via FedEx. They were exceptionally well-packed, arriving in a wood crate filled with packing peanuts. They arrived much faster than I expected, I ordered them on 10/2 and received them on 10/17. Keep in mind these are totally custom doors (size, edging, panels, etc) so that turnaround time is surprising. I work for a general contracting firm, so of course the guys in the office were as curious to pry open the crate as I was. The doors look great, I'll post some pictures tonight or tomorrow. However, I paid extra ($1 per door) to have 35mm holes bored for the hidden Euro hinges, but they forgot to bore them before shipping them to me. Oh well...it was only $4 total, so I'm not going to worry about it. I'll just call around to some local cabinet shops and see if they can bore the holes for me on a walk-in after work.
Tonight I'm going to build a mock-up access panel and see if the Rockler or the Euro hinges I bought will allow the access panel to swing open, without binding the trim. See my previous post (with pictures) for details, if you missed it. Of course I'll let you guys know how it goes, with a nerdy write-up and a couple of pictures.
Take care folks and thanks for showing so much interest!
Dustin
To fix this, I used my rotary saw, with the blade depth lever completely loose, allowing the blade to move up & down freely. I positioned the saw blade where it needed to be, with the saw base against a straight edge, and slowly lowered the blade down and into the plywood. Once all the way seated, I pushed the saw along the straight edge. The corners were finished with the jig saw, handheld, by eye. Here's the result, a much straighter cut:
At this point I packed all the screw/nail holes and wood imperfections with Elmer's wood filler, to be sanded smooth later.
The following day I began the crown molding. Wow...what a pain in the butt. I had three 8' lengths of pre-primed pine crown from Home Depot, and ended up going through all of it before getting things right. The miter cut angles have to be perfect, otherwise the pieces will never line up in the same plane with each other, and you get a resulting bad joint that must be packed with wood filler and sanded. This removes the clean corner of the joint, and leaves a slight rounded look, but hey....whatever. I was just glad to be finished with this stage of the build.
I covered the vertical plywood edge of the left/right shelf sections with this simple pine trim from Home Depot. It has very subtle fluting, to distinguish it from the shelf trim, while helping it match the fully fluted trim columns on the bottom section. I think it ties the two trim selections together nicely.
The top section, almost complete. Just needs the access panel to be installed.
The two sections together, thus far.
The custom cabinet doors arrived at my office today from www.advantagecabinetdoors.com via FedEx. They were exceptionally well-packed, arriving in a wood crate filled with packing peanuts. They arrived much faster than I expected, I ordered them on 10/2 and received them on 10/17. Keep in mind these are totally custom doors (size, edging, panels, etc) so that turnaround time is surprising. I work for a general contracting firm, so of course the guys in the office were as curious to pry open the crate as I was. The doors look great, I'll post some pictures tonight or tomorrow. However, I paid extra ($1 per door) to have 35mm holes bored for the hidden Euro hinges, but they forgot to bore them before shipping them to me. Oh well...it was only $4 total, so I'm not going to worry about it. I'll just call around to some local cabinet shops and see if they can bore the holes for me on a walk-in after work.
Tonight I'm going to build a mock-up access panel and see if the Rockler or the Euro hinges I bought will allow the access panel to swing open, without binding the trim. See my previous post (with pictures) for details, if you missed it. Of course I'll let you guys know how it goes, with a nerdy write-up and a couple of pictures.
Take care folks and thanks for showing so much interest!
Dustin
Last edited:
RedEDGE2k1
Member
It comes in blocks, I think they were something like 4 5/8" x 6 1/4" each. For the top cap I bought a two simple flat-faced pieces; for the bottom cap I bought two with a little routed detail along the top. I cut them down to size with the miter saw.
RedEDGE2k1
Member
The custom cabinet doors, fresh off the FedEx truck. These are paint-grade poplar, sanded very smooth.
I was very impressed with the quality. Well worth the $28/ea price tag.
Access panel hinges, #28845, from Rockler. Big thanks to cannarella for suggesting them, as I'm pretty sure (after reviewing several types of hinges from several different manufacturers) that these are the only ones that would work for my purpose. Cheap, too, at $6.99 per pair. I bought one pair to test on a mock-up, before gluing anything into my cabinet or doing any further modifications.
Here, the mockup works great, without trim. These are interesting little hinges, they actually push the door out about 1/4" before lifting it up. Exactly what I needed to happen. Next I added trim to the gap, hoping it would still work.
1.25" Pine chair railing trim, with about 3/16" overlap, to cover the seam between the two plywood panels.
The door open.....and it works! Flawlessly. The hinges even have springs inside them, so the door stays open automatically, and also closes snug.
I was very impressed with the quality. Well worth the $28/ea price tag.
Access panel hinges, #28845, from Rockler. Big thanks to cannarella for suggesting them, as I'm pretty sure (after reviewing several types of hinges from several different manufacturers) that these are the only ones that would work for my purpose. Cheap, too, at $6.99 per pair. I bought one pair to test on a mock-up, before gluing anything into my cabinet or doing any further modifications.
Here, the mockup works great, without trim. These are interesting little hinges, they actually push the door out about 1/4" before lifting it up. Exactly what I needed to happen. Next I added trim to the gap, hoping it would still work.
1.25" Pine chair railing trim, with about 3/16" overlap, to cover the seam between the two plywood panels.
The door open.....and it works! Flawlessly. The hinges even have springs inside them, so the door stays open automatically, and also closes snug.