Custom Cabinet for 90g Reef (Build Thread)

[RedEDGE2k1]

<a href=showthread.php?s=&postid=11070698#post11070698 target=_blank>Originally posted</a> by cannarella
Your holes for the return will need to be bigger unless you plan on putting in the tank with the unions already on it. I had a hell of a time getting my unions good and snug through the access holes I created. It is quite difficult to get a wrench up there when going through the hole.

I'm not sure I follow you on this?

I'm planning to tighten the bulkheads on the tank, then place the tank w/ bulkheads on the stand (aligning the bulkheads with the holes, then sitting the tank down). My bulkheads have 1-1/4" threaded male ends, and the holes in the cabinet are 2-1/2".

 

[RedEDGE2k1]

This weekend I got a lot of final finish work accomplished on the cabinet...a full weekend of it.

Friday night I skim-coated the entire cabinet exterior with Elmer's Wood Filler (with water added to make it a little more gooey). I didn't bother with the inside areas of the cabinet, as they will be unseen and I don't care if the wood grain is visible in those areas.

I spent all day Saturday sanding the wood filler on the bottom section with 220 grit sandpaper, followed by 320 grit. I had to do this by hand with a sanding block because the power sander was removing the wood filler from the wood grain, even with 320 grit sand paper and light pressure. I was able to finish the bottom section by the end of the night Saturday.

Today (Sunday) I tackled the top section. By 5pm I was finished, and was ready to clean all the dust off the two cabinet sections. I went to Lowe's to buy some tack cloths, but instead came home with a new Porter-Cable air compressor. The $169 was worth every penny, as I was able to blow all the dust particles off the entire cabinet in about 20 minutes. Plus, it'll come in handy for future projects, as I can use it to power nail guns.

Note how visible the wood grain is now. The wood filler dries white. This gives you an idea of how many divots are in oak wood grain. I could have saved myself $60 ($10 per sheet of plywood) and ~16hrs of labor if I would have just used paint-grade ply! Blah...live & learn.

I did a little mutli-tasking today also. I masked off the tank with plastic and 2" painter's tape in preperation for painting, and placed it on a 9'x12' plastic sheet in my garage. For paint, I used American Tradition gloss black enamel spray paint from Lowe's. I bought one can, but ended up going back for a second when the first ran out. I used two full cans on the tank, with probably 12-15 very light coats. I painted the sides and back of the tank, as only the front panel is viewable in my cabinet.

I sprayed very light coats, allowing 20-30 minutes between each thin coat.

The tank complete after two cans of paint and probably a dozen very light coats. I didn't spray the tank while the cabnet sections were in the garage; this picture was taken after I had put everything back in the garage and closed shop for night.

 

[Kreeger1]

Next time use birch plywood and save 10 steps
looking good

 

[cannarella]

Well if you had to do maintenance on the bulkhead it may be difficult to get a wrench on it.

 

[RedEDGE2k1]

<a href=showthread.php?s=&postid=11071141#post11071141 target=_blank>Originally posted</a> by Kreeger1
Next time use birch plywood and save 10 steps
looking good

Ehh...I don't know man. Even the birch stuff at Home Depot wasn't smooth, it didn't have an oak grain texture by any means, but it didn't feel any more smooth than the oak ply. I went with the oak stuff because my girlfriend and I both agreed it felt smoother.

Even with birch or the "sanded ply" they sell, I still think I'd have to skimcoat it with wood filler and sand it smooth in order to get a smooth-as-glass final finish.

 

[cannarella]

<a href=showthread.php?s=&postid=11071204#post11071204 target=_blank>Originally posted</a> by RedEDGE2k1
Ehh...I don't know man. Even the birch stuff at Home Depot wasn't smooth, it didn't have an oak grain texture by any means, but it didn't feel any more smooth than the oak ply. I went with the oak stuff because my girlfriend and I both agreed it felt smoother.

Even with birch or the "sanded ply" they sell, I still think I'd have to skimcoat it with wood filler and sand it smooth in order to get a smooth-as-glass final finish.

You can also get preprimed plywood. Don't know the costs but it may be expensive. Atlanta Hardwoods probably carries it.

 

[Tank Predator]

i gotta say looking awesome doing a great job insperation for me to get cracking on my stand for my 90 i need one reallly bad

 

[FUA]

I don't remember what it is called but they do make plywood that has paper, like drywall paper, on the surface of the plywood. We use it a lot at work because we often but decals and painted murals and stuff right on the plywood. The final product when painted is very smooth. It probably isn';t more than oak plywood.

 

[cannarella]

That would be MDO plywood. It probably is more expensive.

 

[RedEDGE2k1]

<a href=showthread.php?s=&postid=11071204#post11071204 target=_blank>Originally posted</a> by RedEDGE2k1
Ehh...I don't know man. Even the birch stuff at Home Depot wasn't smooth, it didn't have an oak grain texture by any means, but it didn't feel any more smooth than the oak ply. I went with the oak stuff because my girlfriend and I both agreed it felt smoother.

I'm officially taking back everything I said about birch plywood. I stopped by Home Depot today to look at the birch stuff out of curiosity, and I wanted to slap myself in the face for not buying it instead of the oak ply. I must have been looking at something else when I decided the oak ply was smoothest. The birch today had no grain divots, and was totally smooth. I could have saved myself four days of labor and $40 in sanding sealer/sandpaper if I would have known to buy birch. The freakin cabinet would already be finished and in my living room.

Hindsight....blah.

 

[mlrtime99]

Haha a bit ironic, last night I picked up 2 4'x8' sheets of 3/4 Birch for my stand build. I agree it's got a great finish. After reading your heroic sanding/finishing adventure I figured it well worth the 5 bucks more. They also had a couple 2'x4' and 4'x4' precut 3/4 Birch which were great dimensions to cut the sides from. Lowes that is.

 

[RedEDGE2k1]

Yeah, pretty darn frustrating.

With all the wood filler and sand paper I went through, I probably could have made the $25 construction grade plywood smooth

Ok, no more talking about it, I'm trying to forget it and move on!

 

[SUPERHERO2943]

I've been following your build for a while now, and I just have to say that you are doing an awsome job. The stand looks fantastic. I'll be starting my own build in the next month or so for a 125 gallon stand. It will not be nearly as detailed as yours but I may have to PM you if I run up on any questions or snags. Awsome work, can't wait to see the finished product.

 

[RedEDGE2k1]

After tallying up all my receipts, I've spent $908 building the cabinet. This includes everything needed to finish the cabinet (sandpaper, paint, brushes, etc). The only thing that total doesn't include are the tools purchased for/during the build. Really not bad (especially if you already own the power tools), considering a mass-manufactured solid wood stand/canopy combo will run you $600-$800 in stores.

The cherry stand/canopy I was considering purchasing a few months ago at Marine Fish here in Atlanta was $800....and that's for a plain-jane setup that looks like what everone calls a "fish tank stand." I didn't want that...I wanted a piece of furniture that would add appeal to our living room, not take away from it. I think I've accomplished that, and I think my money has been well-spent.

If you can't tell...I highly recommend DIY

 

[todd rose]

Been following your build. Great job!

 

[RedEDGE2k1]

After work this evening I brushed on a coat of sanding sealer to the outside of the top & bottom sections. I'll sand with 320 grit sandpaper tomorrow evening, and hopefully get the first coat of primer on if I have the energy.

 

[Myrddraal]

Very very nice work, I just read your whole thread. One question I have is how are you going to position your vortechs once the stand is assembled and the tank in place? Is there going to be enough room from the access panel to get your arms down to the sides of the tank to move them around?

 

[RedEDGE2k1]

<a href=showthread.php?s=&postid=11083433#post11083433 target=_blank>Originally posted</a> by Myrddraal
Very very nice work, I just read your whole thread. One question I have is how are you going to position your vortechs once the stand is assembled and the tank in place? Is there going to be enough room from the access panel to get your arms down to the sides of the tank to move them around?

The top is removable. Heavy, but removable.

I plan on positioning the VorTech while the top section is off of the bottom section. There is 3" of space between the side glass and the inside of the cabinet, so I'll be able to position the top section back onto the bottom section without touching the VorTech.

I realize it'll be a pain to remove the top section, but I don't intend to remove it very often, once everything is set up and in place initially. I'm going to try and keep my hands out of the tank this time

 

[CKreef]

I'm going to try and keep my hands out of the tank this time


Good luck with that!!!! LOL

 

[mlrtime99]

<a href=showthread.php?s=&postid=10959460#post10959460 target=_blank>Originally posted</a> by cannarella
NOOOOOOOO MDF.

I of course didn't pick up enough Birch ply buy I do have a 4'x8' sheet of 3/4 mdf that I'm thinking of using as a base with acrylic paint, what's so bad about MDF? I know it acts like a sponge by I'd think the acrylic paint would do a decent job of sealing it.