Jebao WP25 Information
- Thread starter Sacohen
- Start date
Sacohen
New member
True.
You see very few comments that say "I love this, it kicks a__". unless they are from when the person just got the pump.
I'm had my WP-25 and 40 since they basically came out and have had little to nor toruble with them.
The WP-40 is going on a year I believe and still running as good as the day I got it. Yes it slows down a bit, but once you clean it it is right back to new.
After following 94 pages, the strong consensus I get,.... is that people are happy with the pumps performance and overall cost. For those who bough the pumps from Fishstreet also get what I consider a ironclad warranty.From the posts I've read, they replace any part issues,...no questions asked. And for me the price can't be beat,... under a hundred bucks,...I'll shelf mine if it quits, buy a new one, and still be hundreds ahead. I find it hard to argue the negative side of the pumps. My two cents worth 
Furballnow
New member
I was one of those people until my pump stopped working today with just 4 months in. Used to be a firm believer.
Don't stop. LoL every brand has their dud. Only typically cost a boatload more. But you did only buy it 4 montgs ago, but cannot remember where? You can probably just go back on a bank or cc statement to see. Or maybe bought it used? Have you tried other pumps with those controllers and p/s? Maybe not the origional or just a bad power supply
Sacohen
New member
Every product has it's bad batches or problem children that happen to get past QC.
I just got a recall for my 2007 Chevy HHR that there is a defect with the ignition switch that will allow the car to be turned off while in gear and driving.
Obviously this in not good because once the engine goes off you loose power to everything including power steering.
Long story is that unfortunately you got a bad unit.
The problem comes to be that you can't remember where you got it from to have it repaired or replaced under warranty.
I just got a recall for my 2007 Chevy HHR that there is a defect with the ignition switch that will allow the car to be turned off while in gear and driving.
Obviously this in not good because once the engine goes off you loose power to everything including power steering.
Long story is that unfortunately you got a bad unit.
The problem comes to be that you can't remember where you got it from to have it repaired or replaced under warranty.
Not a good example Sacohen as that recall affects just about every gm vehicle 2005-9ish iirc. They just haven't released it on all vehicles. It is a faulty retained ring in tge ingition. Yes, I used to work for them lol.
But the principle is correct. There are more people out there replacing parts yearly, or more often, on their $300 circ pumps. Hence why replacement parts are so readily available for vortech mp's
But the principle is correct. There are more people out there replacing parts yearly, or more often, on their $300 circ pumps. Hence why replacement parts are so readily available for vortech mp's
Meanwhile my 10 year old Tunzes keep doing their job. They don't need to be cleaned every few weeks, they have not had any parts replaced from failure, they just silently do what they are supposed to.
Furballnow, try the pumps with a known good power supply, it is usually the weakest part on those pumps.
Furballnow, try the pumps with a known good power supply, it is usually the weakest part on those pumps.
True enough in any case. I have an MJ that I have had for longer then I can remember.
I do not clean my WP's. They are too strong to run at full power anyways. My zoas and softies were staying closed because I had too much flow lol.
I really like the power supply idea.
Furballnow
New member
Dude...I got quite a few of these pumps. Two 10s, one 40, and a pair of 25s so pardon me if I can't recall where I got it. You need pics too?
Furballnow
New member
The controller still lit up so I'm guessing the power supply is still good? Either way I'll try that in a bit. Thnx!
Or enough power, but not enough amps or push of the 24v
Furballnow
New member
You want me to beam you up Scotty..I meant Stevie.
reefdude135
New member
Hi all..... I am trying to clean my WP-25 and am having a heck of a time getting the cover off. Can anyone offer dis-assembly tips?
reefdude135
New member
wow that was easy. I was trying to pry it open like a tunze. thanks!!!
