Brent Thomann
New member
I'm setting up a new apex, only have a temp probe plugged in with 2x EB8 & two heaters. once a day or so my temp probe reading will go from the correct 75 degrees to 19 to 20 degrees triggering my heaters on of course. I unplug the apex resetting it and this fixes it. but then a day later same thing, look at my apex and the temp reads 19 or 20 degrees again. Like theres no probe plugged in.
Any suggestions? Very Frustrating, this is only 1 week old.
Same thing happens to the PH reading, drops at the same time. I don't have a PH probe plugged in so the reading is always around 3.65 ph normally. At the same time the temp reading drops to 20 my ph reading drops from approx 3.65 to approx 2.60 ph. after I reset the apex it goes back to the normal 3.65
22:10 04/15/2011 75.2 3.35 921 0.0 0.0
22:20 04/15/2011 75.2 3.65 921 0.0 0.0
22:40 04/15/2011 19.3 2.60 921 7.7 0.0
22:50 04/15/2011 19.3 2.60 921 7.7 0.0
reset-
00:50 04/16/2011 19.3 2.60 921 7.7 0.0
01:00 04/16/2011 19.3 2.60 921 7.7 0.0
01:10 04/16/2011 78.2 3.85 921 0.0 0.0
01:20 04/16/2011 78.2 3.67 921 0.0 0.0
problem happened again from yesterday-
22:10 04/15/2011 75.2 3.35 921 0.0 0.0
22:20 04/15/2011 75.2 3.65 921 0.0 0.0
22:40 04/15/2011 19.3 2.60 921 7.7 0.0
22:50 04/15/2011 19.3 2.60 921 7.7 0.0
prior time it happened (no heaters plugged in yet, notice PH didn't change?)-
19:00 04/13/2011 71.8 2.60 921 0.0 0.0
19:10 04/13/2011 71.8 2.60 921 0.0 0.0
19:30 04/13/2011 19.3 2.60 921 0.0 0.0
19:40 04/13/2011 19.3 2.60 921 0.0 0.0
prior time it happened (no heaters plugged in yet)
18:40 04/11/2011 73.1 2.60 921 0.0 0.0
18:50 04/11/2011 73.0 2.60 921 0.0 0.0
19:00 04/11/2011 19.3 2.60 921 0.0 0.0
19:10 04/11/2011 19.3 2.60 921 0.0 0.0
time prior-
03:40 04/10/2011 72.4 2.60 921 0.0 0.0
03:50 04/10/2011 72.4 2.60 921 0.0 0.0
04:00 04/10/2011 19.3 2.60 921 0.0 0.0
04:10 04/10/2011 19.3 2.60 921 0.0 0.0
Any suggestions? Very Frustrating, this is only 1 week old.
Same thing happens to the PH reading, drops at the same time. I don't have a PH probe plugged in so the reading is always around 3.65 ph normally. At the same time the temp reading drops to 20 my ph reading drops from approx 3.65 to approx 2.60 ph. after I reset the apex it goes back to the normal 3.65
22:10 04/15/2011 75.2 3.35 921 0.0 0.0
22:20 04/15/2011 75.2 3.65 921 0.0 0.0
22:40 04/15/2011 19.3 2.60 921 7.7 0.0
22:50 04/15/2011 19.3 2.60 921 7.7 0.0
reset-
00:50 04/16/2011 19.3 2.60 921 7.7 0.0
01:00 04/16/2011 19.3 2.60 921 7.7 0.0
01:10 04/16/2011 78.2 3.85 921 0.0 0.0
01:20 04/16/2011 78.2 3.67 921 0.0 0.0
problem happened again from yesterday-
22:10 04/15/2011 75.2 3.35 921 0.0 0.0
22:20 04/15/2011 75.2 3.65 921 0.0 0.0
22:40 04/15/2011 19.3 2.60 921 7.7 0.0
22:50 04/15/2011 19.3 2.60 921 7.7 0.0
prior time it happened (no heaters plugged in yet, notice PH didn't change?)-
19:00 04/13/2011 71.8 2.60 921 0.0 0.0
19:10 04/13/2011 71.8 2.60 921 0.0 0.0
19:30 04/13/2011 19.3 2.60 921 0.0 0.0
19:40 04/13/2011 19.3 2.60 921 0.0 0.0
prior time it happened (no heaters plugged in yet)
18:40 04/11/2011 73.1 2.60 921 0.0 0.0
18:50 04/11/2011 73.0 2.60 921 0.0 0.0
19:00 04/11/2011 19.3 2.60 921 0.0 0.0
19:10 04/11/2011 19.3 2.60 921 0.0 0.0
time prior-
03:40 04/10/2011 72.4 2.60 921 0.0 0.0
03:50 04/10/2011 72.4 2.60 921 0.0 0.0
04:00 04/10/2011 19.3 2.60 921 0.0 0.0
04:10 04/10/2011 19.3 2.60 921 0.0 0.0