Programming the OceanRevive Arctic T247

PoggiPJ

PoggiPJ

Premium Member
After struggling through the somewhat cryptic User's Manual and with help from my fellow reefers here, I think I finally figured out the basics of the unit and how to control my settings.

This is not to say that the manual provided is incorrect. It is correct. I am only saying that as someone without any prior exposure to the unit, I found it a bit difficult to follow.

So I thought I would write and post an "alternative" set of instructions for programming the unit using the remote. I have also attached the information as a MS Word Document for your convenience. I welcome your feedback. If you find something here to be incorrect I will edit the post and attach a corrected document.

Ocean Revive Artic T247 Basics
The Artic T247 features two separately controlled color channels, each of which can be set to their own Intensity, Time On, and Time Off functions. Channel 1 controls the blue LEDs, Channel 2 controls the white LEDs. When either of the two channels turn on, the intensity percentage for that channel is fixed at the last setting selected, and cannot be programmed to increase or decrease over time.

Programming the Arctic T247 using the Remote
The remote is not paired to a specific unit. If you have multiple T247 units be sure to aim the remote at the desired unit or you can make unintended changes to your other units. If necessary, fold an index card in half, and place it over the displays of the other units to block them from the remote signal.

Besides turning the entire unit On or Off, you can use the remote to individually set or change any of the following features.
  • Preview the current settings
  • Current time
  • Channel 1 On
  • Channel 1 Off
  • Channel 1 Intensity %
  • Channel 2 On
  • Channel 2 Off
  • Channel 2 Intensity %
Each of the above features can be individually set, meaning you do not have to go through ALL of the features if you only want to change a single setting.
Tips:
  1. All times are displayed in 24:00 hour time format, where noon is 12:00, 1:00 PM is 13:00, and so on up to Midnight 24:00.
  2. The lower section (2 rows of 3 buttons) are only associated with Channel 1 and 2 on and off times and have nothing to do with channel intensity.
  3. If the unit senses a three second delay at any point during programming, it will automatically save any changes and return to the current time display.
  4. When setting the Channel 1 on or Channel 2 off times, do not press the OK button. The OK button is used to set channel intensity.
  5. When setting the Channel intensity percent, you will be using the OK, Up arrow, and Down arrow buttons.

Set the current time
Press the MENU button. The display will change from current time (HH:MM) to HS-E, indicating it is ready to program.

Press the CLOCK button. The display will change from HS-E to CLoC.

Press the right arrow once and the hours (HH:--) will blink.
Press the Up arrow to select the hour. Press the right arrow once and the minutes (--:MM) will blink. Press the Up arrow to select the minutes.
If you do not press another button for three seconds, the current time selections will automatically save. The display will change to HS-E, then to current time.​

Set the Channel On and Off times
Tip: The channel 1 and channel 2 on and off times are set individually

Channel 1 (Blue) On and Off Times
On: Press the MENU button. The display will change from current time (HH:MM) to HS-E, indicating it is ready to program.
Press the C1 ON button. The display will change from HS-E to C1 on. Press the right arrow once and the hours (HH:--) will blink. Press the Up arrow to select the hour. Press the right arrow once and the minutes (--:MM) will blink. Press the Up arrow to select the minutes.

If you do not press another button for three seconds, the current selections will automatically save. The display will change to HS-E, then to current time.

Off: Press the C1 OFF button. The display will change to C1 oF. Press the right arrow once and the hours (HH:--) will blink. Press the Up arrow to select the hour. Press the right arrow once and the minutes (--:MM) will blink. Press the Up arrow to select the minutes.
If you do not press another button for three seconds, the current selections will automatically save. The display will change to HS-E, then to current time.

Channel 2 (White) On and Off Times
Press the MENU button. The display will change from current time (HH:MM) to HS-E, indicating it is ready to program.
On: Press the C2 ON button. The display will change from HS-E to C2 on. Press the Right arrow once and the hours (HH:--) will blink. Press the Up arrow to select the hour. Press the Right arrow once and the minutes (--:MM) will blink. Press the Up arrow to select the minutes.
If you do not press another button for three seconds, the current selections will automatically save. The display will change to HS-E, then to current time.
Off: Press the C2 OFF button. The display will change to C2 oF. Press the Right arrow once and the hours (HH:--) will blink. Press the Up arrow to select the hour. Press the Right arrow once and the minutes (--:MM) will blink. Press the Up arrow to select the minutes.
If you do not press another button for three seconds, the current selections will automatically save. The display will change to HS-E, then to current time.

Set the Channel Intensity
Tip: The channel 1 and channel 2 intensity are set individually. Intensity is controlled as a percentage, from zero (off) to 100 (full intensity)
Channel 1 (Blue) Intensity
Press the OK button once. The display will change from current time (HH:MM) to HS-E, indicating it is ready to program. Press the OK button once more. The display will change from HS-E to CH1. Press the Right arrow once and current intensity percent will appear ( 30). To increase or decrease the intensity for this individual channel, press the Up arrow or Down arrow respectively. Each press of the arrow button will either increment or decrement the intensity by one percent, indicating the new intensity for that channel. For example, five presses of the Up arrow will result in 35.​
Channel 2 (White) Intensity
Press the OK button once. The display will change from current time (HH:MM) to HS-E, indicating it is ready to program. Press the OK button a 2nd time. The display will change from HS-E to CH1. Press the OK button a 3rd time. The display will change from HS-E to CH2. Press the Right arrow once and current intensity percent will appear ( 30). To increase or decrease the intensity for this individual channel, press the Up arrow or Down arrow respectively. Each press of the arrow button will either increment or decrement the intensity by one percent, indicating the new intensity for that channel. For example, five presses of the Up arrow will result in 35.​

Preview the Settings
At any time during or after programming, you may review the settings to verify they were set successfully. Press the Preview button once. The display will cycle through the following four settings before returning to displaying current time.
C1 on (channel 1 on time)
HH:MM
C2 oF (channel 1 off time)
HH:MM
C1 on (channel 2 on time)
HH:MM
C2 oF (channel 2 off time)
HH:MM
 

Attachments

Thank you for taking the time to write this up. I ordered 2 of these yesterday, and now feel well prepared to program them.
 
Additional Information

Additional Information

I wish I could edit the original post. The morning after posting that I came downstairs to find that only one unit was on. The other two never turned on automatically as I expected. As it turns out, there's one more step required to assure that the channels turn on or off automatically based on your time settings. It's stated in their instructions, but I didn't understand the context when I first read it. I will attach a new version of the document with the additional information to this post.

When you are not programming them, the units will remain in one of three operating modes: HS-E, CH1, or CH2. The units must be left in HS-E mode in order for the time settings to be active.

You can tell which mode you are in by pressing the dimmer button once. It should read HS-E. If it reads CH 1 or CH 2, then continue to press the dimmer button once until the display cycles to HS-E, then leave it alone. It will eventually return to the time display.
 

Attachments

Last edited:
PoggiPJ said:
If you received a little fold-out about 1/4 the size of a standard page, that was it. There is one on their site that you can download
Click to expand...

Not a single piece of paper in any of the three boxes I got. I have not installed them yet but I printed your latest word doc to program them once I get to installing them!
 
Yes, I believe they are here, just more active on the another forum, which I guess I cannot mention here because it changed to asterisks.
 
Love my T247's, but customer service stinks. No phone number to call, or no one to contact for issues. PoggiPJ you did an outstanding job with the directions, and much better than what comes in the box.

I've got both lights programed, and one works as designed, but the 2nd one does not fully shut off. The whites turn off, but the blues stay on. I've tried using the remote control and the knob, both to no avail. The only way I can get the blues to cut off is to unplug the unit. Can you provide any help? Thx [emoji31]
 
Quick update. I did get a response back to my email, but still haven't been able to resolve my issue. They think it may be related to the timer. In my correspondence, OceanRevive also sent me PoggiPJ's word doc instructions from this post to help me trouble shoot.
 
Update, sent Stan the OR rep an invite to join in here. If he decides not to join in on this post I'll start a new thread about OceanRevive customer service.
 
Thank you for posting this. Don't have one yet, but looking into this fixture in the near future so will definitely be referring back to this.
 
Great job Pete! I wish I would have seen your post when i was programing my light. I think what we have run into with these chinese built lights instructions, is there is a translation problem. We all may have run into that with other Chinese built products.
 
DTdr2 said:
Update, sent Stan the OR rep an invite to join in here. If he decides not to join in on this post I'll start a new thread about OceanRevive customer service.
Click to expand...

Keep me updated my timer just kicked the can. I have the light just running on a coralife timer and power outlet, manually adjusting the channels.


As soon as I cycle to HS-E mode the lights cut out, I can program time but the timer will not keep current time and will revert back to 00:00. Kind of an annoyance, but will get fixed soon I hope.
 
hcl2195 said:
Great job Pete! I wish I would have seen your post when i was programing my light. I think what we have run into with these chinese built lights instructions, is there is a translation problem. We all may have run into that with other Chinese built products.
Click to expand...

Yes, I have run into this before. I may take a post -retirement job of rewriting instructions for Chinese companies. They take their best shot, but the languages are so different I imagine it's quite a challenge. I still need to add the section and pictures regarding adjusting the length. Just been busy
 
mushumatt said:
Keep me updated my timer just kicked the can. I have the light just running on a coralife timer and power outlet, manually adjusting the channels.


As soon as I cycle to HS-E mode the lights cut out, I can program time but the timer will not keep current time and will revert back to 00:00. Kind of an annoyance, but will get fixed soon I hope.
Click to expand...

Matt, did you make sure that the units were in HS-E mode when you set the CH1 and CH2 on/off times? I ran into a similar problem until I figured out about making sure I was in the HS-E mode. I still haven't figured out what HS-E stands for :-)

Another reason this happened to me, is when I use the knob to change the intensity of either channel, I inadvertently screwed up my on/off times.
 
mushumatt said:
Keep me updated my timer just kicked the can. I have the light just running on a coralife timer and power outlet, manually adjusting the channels.


As soon as I cycle to HS-E mode the lights cut out, I can program time but the timer will not keep current time and will revert back to 00:00. Kind of an annoyance, but will get fixed soon I hope.
Click to expand...
Loved the lights, but ended up sending both lights back for a refund. Had major issues with one, and it ended up going out all together. The 2nd one worked great with the timer (both channels), but I would wake up at night and the blues would be on, would have to unplug it in order to turn it off. Trying to communicate by email at 4:00 a.m. my time got frustrating not to mention spending that much money. I decided to cut my losses short, and will be going another route. Good luck to you. I feel your frustration
 
You must log in or register to reply here.

Similar threads

R
Coralife Chiller Error E1
Replies
1
Views
210
Reefing102
Reefing102
J
Back into the Hobby
Replies
15
Views
794
griss
griss
F
Cannot raise PH levels, aquarium with Calcium Reactor
Replies
1
Views
480
Vinny Kreyling
Vinny Kreyling
NancyT3
Thankful for Dr Reefs QT Fish, Hooked on invertebrates....
Replies
2
Views
519
griss
griss
C
Tunze Osmolator 3152 only works immediately after plugging in
Replies
5
Views
650
asmodeus
asmodeus
Back
Top