Long post sorry
So I bought a g4 pro off ebay about 1 month ago, advertised as serviced and cleaned by xodis in October so sounded like good maintained unit.
It arrived mobius ready so went on mobis and downgraded to stick with reeflink.
Connected to WiFi all working fine. No issues for 2 weeks.
Till one day The leds were flashing on and off and buttons red.
Spoke to eco tech and they asked me look at power brick, it was flickering blue. So that was the problem..
Bad luck but I accepted that.
Couldn't find another meanwell gst220a36et that the light already but electrical guy told me that the gst220a36,r7b is the same thing with a different end that a adapter can fix the tip. All figures the same on the box.
So that came plugged in and all was well i thought. Reprogram lights and all seem fine.
Woke up next day light wasnt on No buttons flashing. Switched on and off and all back again but noticed it didnt change all day then again the next morning it didn't come on at the right time.(power brick stays on) the leds didnt switch on.
Logged into ecosmart and the radion time is out sync, refreshed and set. All good, 5 min later its its gone 2 min while other 1 has gone 5 min. Its going slow
Looked at info and the clock power says no.
So factory reset and clock power yes light stayed on all night doing what it supposed to.
Before I went to bed I looked at info for clock power, that said yes.
Woke up no light. Again.
It was 7.05 and the offending light showed 6.53
So I bit confused to why it seems to have developed a different fault now since new power brick to come and cant keep time properly. But all day when the leds are in it stays in time perfectly fine but seem to run out of time keeping when the leds are off but the main power is consistently on.
Info for clock power then says no. Soon as leds are on it comes back to yes
I am speaking to xodis in the uk butthey said they are not sure and looking to see if they have parts to change the board.
But this light was fine till the brick went wrong.
Why does it look like the leds are powering the memory and when they are off its forgetting.
So I bought a g4 pro off ebay about 1 month ago, advertised as serviced and cleaned by xodis in October so sounded like good maintained unit.
It arrived mobius ready so went on mobis and downgraded to stick with reeflink.
Connected to WiFi all working fine. No issues for 2 weeks.
Till one day The leds were flashing on and off and buttons red.
Spoke to eco tech and they asked me look at power brick, it was flickering blue. So that was the problem..
Bad luck but I accepted that.
Couldn't find another meanwell gst220a36et that the light already but electrical guy told me that the gst220a36,r7b is the same thing with a different end that a adapter can fix the tip. All figures the same on the box.
So that came plugged in and all was well i thought. Reprogram lights and all seem fine.
Woke up next day light wasnt on No buttons flashing. Switched on and off and all back again but noticed it didnt change all day then again the next morning it didn't come on at the right time.(power brick stays on) the leds didnt switch on.
Logged into ecosmart and the radion time is out sync, refreshed and set. All good, 5 min later its its gone 2 min while other 1 has gone 5 min. Its going slow
Looked at info and the clock power says no.
So factory reset and clock power yes light stayed on all night doing what it supposed to.
Before I went to bed I looked at info for clock power, that said yes.
Woke up no light. Again.
It was 7.05 and the offending light showed 6.53
So I bit confused to why it seems to have developed a different fault now since new power brick to come and cant keep time properly. But all day when the leds are in it stays in time perfectly fine but seem to run out of time keeping when the leds are off but the main power is consistently on.
Info for clock power then says no. Soon as leds are on it comes back to yes
I am speaking to xodis in the uk butthey said they are not sure and looking to see if they have parts to change the board.
But this light was fine till the brick went wrong.
Why does it look like the leds are powering the memory and when they are off its forgetting.
