Stand support question about removing 2x4

[itz frank]

So, the two 2x4s cause my stand to be only 13 inches wide. This makes it very hard to find a decent sump to use because my tank is 130 gallons and I can't fit anything more than 24" long as a sump below.

If I remove these two 2x4, will I compromise the load bearing weight of the stand?


Sent from my iPhone using Tapatalk

 

[reefer1970]

So you have a double 2x4 front and back in the center? And want to remove 1 on the front and 1 back to gain 3"? Should be fine, looks like the rest one isn't doing anything anyway. You can add one next to the existing one on the rear.


Sent from my iPhone using Tapatalk

 

[reefer1970]

Rear one


Sent from my iPhone using Tapatalk

 

[smedlin]

Did a brace or something use to be on top of that 2x4?

What's the splinted wood from?

 

[itz frank]

Did a brace or something use to be on top of that 2x4?

What's the splinted wood from?

It went all the way up before. I had to cut it to get my plumbing in. It didn't support s cross beam though.

I have one of those on the front and one on the rear.

I want to remove both.


Sent from my iPhone using Tapatalk

 

[smedlin]

It went all the way up before. I had to cut it to get my plumbing in. It didn't support s cross beam though.

I have one of those on the front and one on the rear.

I want to remove both.


Sent from my iPhone using Tapatalk

Well, from the looks of it, technically you have already removed it. It's not doing anything anymore..just attached to the side of that other board, yes?

 

[itz frank]

Well, from the looks of it, technically you have already removed it. It's not doing anything anymore..just attached to the side of that other board, yes?

Yes. Just wasn't sure if it was supporting the other board vertically and it was essential.


Sent from my iPhone using Tapatalk

 

[ericarenee]

on the 2nd picture . You can clearly see the 2x6 behind that 2x4 is a JACK STUD, Meaning its sitting under the load . There is no reason why you cant remove it.. To be save cut a piece of plywood say 5.5 tall by 10 inches and screw it to that 2x6 deck and the 2x6 behind where your removing that 2x4

The first picture looks like there are 2 2x4 if so and the painted one is also a jack do the same with plywood to bridge the deck to the jack and you will be fine.. That stand is WAY OVER BUILT...

Hope this helps

 

[snorvich]

on the 2nd picture . You can clearly see the 2x6 behind that 2x4 is a JACK STUD, Meaning its sitting under the load . There is no reason why you cant remove it.. To be save cut a piece of plywood say 5.5 tall by 10 inches and screw it to that 2x6 deck and the 2x6 behind where your removing that 2x4

The first picture looks like there are 2 2x4 if so and the painted one is also a jack do the same with plywood to bridge the deck to the jack and you will be fine.. That stand is WAY OVER BUILT...

Hope this helps

She is an expert

 

[itz frank]

on the 2nd picture . You can clearly see the 2x6 behind that 2x4 is a JACK STUD, Meaning its sitting under the load . There is no reason why you cant remove it.. To be save cut a piece of plywood say 5.5 tall by 10 inches and screw it to that 2x6 deck and the 2x6 behind where your removing that 2x4

The first picture looks like there are 2 2x4 if so and the painted one is also a jack do the same with plywood to bridge the deck to the jack and you will be fine.. That stand is WAY OVER BUILT...

Hope this helps

Ok. So just for clarification in the picture with the one painted and one unpainted, that's the front. The piece my pointer is touching is the 2x4 and my thumb is the 2x6. The unpainted one is the back. You're saying I can remove both 2x4s, correct?

The 2x6 is also removable? I'm thinking I probably shouldn't touch that one unless you think it's ok.

And I'd agree. The stand has a ton of wood in it.


Sent from my iPhone using Tapatalk

 

[itz frank]

Nvmd. I understand the comment about the 2x6. Thank you for your help.


Sent from my iPhone using Tapatalk

 

[ericarenee]

Nvmd. I understand the comment about the 2x6. Thank you for your help.


Sent from my iPhone using Tapatalk

You are welcome..


Not that it really matters but i am Contractor and own a Renovation company.Of course going off images in a tight place is never a given..

but the key is the 2x lumber that is clearly under the deck(square frame the tank sits on) is what is holding up the weight. Those other 2x are wasted lumber in my opinion.. But because I am not in front of it i Suggested above putting a plywood plate to span the framing members . this will insure proper support in case of any framing gaps (something cut too short...

You can also buy metal plates of verious sizes from big box stores as well.

 

[itz frank]

on the 2nd picture . You can clearly see the 2x6 behind that 2x4 is a JACK STUD, Meaning its sitting under the load . There is no reason why you cant remove it.. To be save cut a piece of plywood say 5.5 tall by 10 inches and screw it to that 2x6 deck and the 2x6 behind where your removing that 2x4

The first picture looks like there are 2 2x4 if so and the painted one is also a jack do the same with plywood to bridge the deck to the jack and you will be fine.. That stand is WAY OVER BUILT...

Hope this helps

Sorry to bring you back to this but I'm in the process of purchasing a new sump and the dimensions of the door frame and depth don't allow me to purchase the one I want.

So, My question is can I remove that back vertical support. Not the cut one but the one that is supporting the cross 2x6 where the weight of the tank is actually on.

This wouldn't be permanent but I would need to remove it to try and place my sump into the stand. I don't want to remove the front one because there is plywood on the outside and cutting into it would leave permanent aesthetic issues.

 

[Sandy Cheeks]

I think you should post a picture of the full stand so people get a better idea on how wide the doors are. I notice the rear stud has what seems finish nails? sticking out. Brings a question, How is the wood fastened together?

 

[ericarenee]

Because its 2x6 and the tank i assume is up and running.. I would move any coral you have up high on the rocks to the bottom of the tank and Drain the tank down to about half or less the ..

Remove it put the sump in and put it back together then refill the tank.. BUT BUT BUT BUT
Be very Careful removing this even if the tank is empty. You Want to cut it out being sure to not put any more or any less pressure onto the 2x6 its carrying..

I would cut two 2x4 put one on each side of the one you are taking out . cut them to fit tight but able to bump out with your hand.. Cut the brace out with a saw-zaw middle ways using two cuts 1/4 inch apart knocking the piece out between cut as you go . this will keep from binding the blade and causing it to shake the tank ... (I WOULD NOT use two cuts but know how saw acts in the wood) Once you have it cut into.. cut the screws at the top and bottom with saw. Do not try to just pull the wood out.. then with your hand you should be able to bump out the temp ones slide the sump in and put them back as perm support all in a matter of minutes ...

The key is Draining the tank down as low as you can .. at least half would be my recommendation.. or Build a acrylic sump in place


Its all about your skills to be honest