2' cube build has officially started!

J

jcm2m9

New member
It's official. My 2' cubish tank has FINALLY started. Scott from Aquatics System design is building my new tank. It is 24" x 24" x 16" acrylic tank. It will be run as an open top.

24x24x16-dim.jpg


24x24x16_bottom-dim.jpg


The main focus of this tank was to have to equiptment visible anywhere. I believe I have sucessfuly done this. All the cl returns will be hidden under the rockwork and will be directed via loc line. The cl pump is a Little Giant 4 MDQX-SC - 1225 GPH @3'.

My sump is 24" x 24" x 17" where my Coralife Super Skimmer 65 will he house. I know this skimmer is small for this tank, but it is going to have to work for now. I will have two heaters in the sump, but I have not decided which ones yet. My return pump will be a Mag 3. I am not wanting to have a high flow through my sump. I am trying to keep this tank very quiet as it will be in my bedroom.

DSC01450.jpg


The lighting for this tank with be a diy hood/pendant that will be suspended above the tank. My lighting is a 250w PFO ballast with a 10k Xm bulb. My supplementation is 2 24" URI superactinics powered by an IceCap 440 ballast.

All of my equipment will be controlled by my new Aquacontroller Jr. It will be set up to use Aquanotes and will be fully controllable via the internet.

I started construction of the stand today. The stand is 36" tall, 25" wide, and 30" deep. The stand was framed with 2"x4" studs with 1/2" plywood on the bottom and doubled up 1/2" plywood on the top. On the top the rear joist was notched to accommodate the drain and return in the overflow box. The entire frame will be painted wit several coats of white primer. The stand will be finished in oak and stained with cherry stain. I will apply quite a few coats of polyurethane. I have not decided if I am going to purchase premade doors or make my own, but I am leaning toward buying them at this time. It will just be one less thing I have to make.

DSC01445.jpg


DSC01448.jpg


DSC01454.jpg


I do not think I will get anymore work done on the stand till the end of next week. It is finals weeks at the University of Missouri - Kansas City and I need to study for my Differential Equations, Dynamics, Circuits, and Therodynamics finals.
 
Looks good !


Are the closed loop returns drilled on the bottom of the tank ? That's a cl big pump for that tank :eek1: .

I like suspended lights, you will too when it's time to do tank maintenence.
 
Re: 2' cube build has officially started!

<a href=showthread.php?s=&postid=7274544#post7274544 target=_blank>Originally posted</a> by jcm2m9


The main focus of this tank was to have to equiptment visible anywhere. I believe I have sucessfuly done this. All the cl returns will be hidden under the rockwork and will be directed via loc line. The cl pump is a Little Giant 4 MDQX-SC - 1225 GPH @3'.

DSC01450.jpg

Click to expand...

Wow! I can't see a single piece of equipment. Keep up the good work!





:lol:

tagging along
 
The holes in the bottom of the tank are for my cl. They are going to be hidden in the rock work and routed out the work via locline.

I ended up getting a practically new Gen-X PCX30 for my cl pump. It only does about 980 gph so that is about a 30x turnover rate. What I like about my design is there will only be about 1' of head on the pump.

I will have ball valves on all of the returns so I can control the flow. Maybe I will get an oceansmotion for my birthday! :D

My sump tank will have plenty of equiptment in it here in a few weeks. Just you wait and see. LOL


Does anyone have a link to Calvin's custom 40g? I would love to look at it.
 
Over the last few weekends I have finished framing the stand and put two coats of white paint on it. I also made a few modifications to make the stand sronger. After while I am going to go get the oak to skin the stand in. Hopefuly I will be able to get most of the oak cut today, but who knows.
Last night I was working on programing my Aquacontroller JR. I looked at CathyJ's to help me along the way. Here is what I have so far. I would like some feedback on it.

Timer Names:
MH1 - Metal Halide
ACT - Actincs
SMP - Sump Light
CL1 - Closed Loop
FAN - Fan to cool tank
HTR - Heater
SKM - Skimmer

Timers:
If time > 11:00 then ACT on
If time > 13:00 then MH1 on
If time > 19:00 then MH1 off
If time > 21:00 then ACT off
If time > 21:00 then SMP on
If time > 11:00 then SMP off

If temp < RT + .5 then HTR on
If temp < RT + .0 then HTR off
If temp > RT + .5 then FAN on
If temp > RT + .0 then FAN off

If temp > RT + 1 then MH1 off
Max Change 20M then MH1 off
If temp > RT +1.2 then ACT off
Max Change 5M then ACT off

If feeding cylce then CL1 off
If feeding cycle then SKM off

If Power Fail then MH of
Max Change 20M then MH off
If Power Fail then ACT off
Max Change 5M then ACT off
If Power Fail then SKM off
Max Change 5 M then SKM off

That is what I have right now. Let me know what you think. Also, a few questions on the programming. Do the timers have to be in order like a "ladder logic" program or does it just run though all the timers and see which is applicable? Basically what i am asking is does the order I enter the timers matter?

Also, how is the best way to calibtrate the temp probe and do I need to buy calibration fluid to calibtrate the ph probe or is it store in calibration fluid now?
 
Here is how I have edited the parameters:

If time > 11:00 then ACT on
If time > 13:00 then MH1 on
If time > 19:00 then MH1 off
If time > 21:00 then ACT off
If time > 21:00 then SMP on
If time > 11:00 then SMP off

If temp < RT + 1 then HTR on
If temp < RT + .5 then HTR off
Max Change 5M then HTR off
If temp > RT + 1 then FAN on
If temp > RT + .5 then FAN off
Max Change 5M then FAN off

If temp > RT + 2 then MH1 off
Max Change 20M then MH1 off
If temp > RT + 2.5 then ACT off
Max Change 5M then ACT off

If feeding cylce then CL1 off
If feeding cycle then SKM off

If Power Fail then MH of
Max Change 20M then MH off
If Power Fail then ACT off
Max Change 5M then ACT off
If Power Fail then SKM off
Max Change 5 M then SKM off

I am trying to keep my temp swings to a minimum. I think this is doable with the controller. I may have to allow for more of a temp swing then 2 degrees. I will just have to wait until I get the tank up and running. Also, I think I am going to revised the lighting parameters to run on the lighting tables that come preprogrammed on the controller.

On Wed. evening I am going to go out and take a few pics of the tank! I can not wait to see it. It is not quite done yet. The actual tank is built, but the holes need to be drilled and the overflow needs to be attached.

Also, I decided not to continue on the stand until I have the tank in my posession. I do not want to have to back track later on if something is not correct.

So right now I am concentrating on getting the Aquacontrollter figured out and curing my cyano in my 29g :evil: . I am sure the filters are dead in my rodi. My new filters should be here soon. I need to do water changes badly, but do not want to use bad water.
 
I have been working on the stand off and on over the last few days. I have all of the wood cut for the exterior of the stand. I just need to go buy trim and attach it all. I am hoping to get some of this done this evening. I am hoping to get some new pictures too.


I need to get the tank before I can trim the top of the stand so I can be sure that the tank fits in the opening perfectly.
 
taging along for the ride. i want to build something similar but a little bit higher(but thats a year or two away)
 
My tank is DONE!

I am hoping to pick it up and my loc-line on Friday evening or Saturday! I will get pictures up as soon as I can!
 
I just got back from picking up my tank and working on the stand. I am sooooo excited. The tank looks better then I imagined. My favorite part is the addition af teeth on the overflow. I had not even thought about that, but Scott thought I would want them. However, in case I did not want them he just screwed the row of teeth on and when you take the teeth off you would never even know they were there. It is awesome!

The craftsmanship is INCREDIBLE. Tomorrow I am hoping to start triming the stand. I have quite a bit of work left to do. I also need to start thinking about how I am going to build the doors.

I decided not to put a door on the front. I really was not needed. I can get to everything from both sides. Plus, since I used 1/4" oak plywood the extra brace in the front is going to help with potential warping. I think I am going to attach my closed loop pump to that new front brace so I do not have to build a shelf. There really is not much room for a shelf.

Does anyone know where I can buy Spa Flex?

Here are some pictures.

DSC01455.jpg


DSC01456.jpg


DSC01457.jpg


DSC01460.jpg


DSC01462.jpg
 
After a long Memorial Day weekend of moving my girlfriend I finally had a few hours this evening to work on the stand a little more. I was able to get the trim on the top and bottom of the stand and started filling the top back right and left corners of the stand on the sides of the overflow box. I need to go and get some corner for the corners of the tank. I also need to make doors for the stand, but I believe that is going to wait until after I have the tank up and running.

I am leaving on a fishing trip to Canada on Thursday night, so i am not sure how much more I am going to get done before then. As soon as I get back I am going to get the trim finished and start sanding and then sand some more.

The final product is getting closer and closer. I am very anxious.

Here are a few pictures of the progress.

DSC01465.jpg


DSC01466.jpg


DSC01468.jpg
 
Now that I am back from my wonderful vacation I have had some time over the last few days to work on the stand. I finished getting the stand trimmed out, then got it sanded, cleaned off, applied the pre-stain and then stained it. I am pretty pleased with the stand at this point. There are a few things I would have done differently. I guess you live and learn.


What have yet to figure out is how I am going to do the lighting. I have the MH ballast and reflector and the VHO ballast, end caps and bulbs. I want to have a pendant style lighting setup. The only problem is that I do not want to spend all the money to buy a MH/VHO pendant. I was going to see if I could find a metal shop that would make me a pendant out of sheet metal and then I would paint it black. I just do no know of any where that would do this for me. Any suggestions? My only other options is to build one out of pine. If I can not find somewhere to make me a pendant out of sheet metal, this is what I am going to have to do.

Trim finished -
DSC01471.jpg


Materials -
DSC01473.jpg


pre-stain treatment applied -
DSC01472.jpg


Stained -
DSC01474.jpg


DSC01476.jpg
 
You must log in or register to reply here.

Similar threads

Brian60077
Big project starting today......
Replies
7
Views
539
Dustin07
D
adova
300g DIY Acrylic Tank Recommendations
Replies
5
Views
424
griss
griss
U
New build
Replies
3
Views
595
griss
griss
DjPhato
Ready, set…water! 90gal peninsula build
2
Replies
26
Views
1K
Patrick Seastar
Patrick Seastar
S
Looking at building a diy wood tank and stand
Replies
1
Views
502
Vinny Kreyling
Vinny Kreyling
Back
Top