Bobbitworm13
New member
What lfs do you use? I am in Kentucky and have only been to pet central in bowling green. It has good stock but not much selection
Devoted Reefer 250
- Thread starter pelphrey
- Start date
pelphrey
New member
I have the Fish Doctor right up the road from me. They always have a nice selection of fish and they just got a nice coral table filled. Since you are closer to Nashville than I am you should visit Aquatic Critter, I will be going back. Also Aquatica in Louisville is a good store!
Bobbitworm13
New member
What lfs do you go to? I'm in Kentucky as well and have only been to pet central in Bowling Green. It seems like it has good stock but they don't have a lot of selection
Bobbitworm13
New member
Oops double posted
Bobbitworm13
New member
Ok I've seen aquatica, it's about two hours from me
pelphrey
New member
Aquatica and Aquatic Critters are both just at 2 hours for me. It's nice to be able to go in and pick your livestock but as far as time I am not sure how many trips I'll make. I usually spend enough money to qualify for free shipping for most online retailers.
pelphrey
New member
Thank you!!! You will be very happy with the reefer series tanks!
pelphrey
New member
Wanted to try out an Algae Turf Scrubber, when I got the chance to grab the Santa Monica RAIN2 I jumped on it. I haven't got it installed on the tank just yet!
GEM5 lights
Currently there is 1 GEM5 light installed in the ATS. I do have all 4 lights and will install them as needed!
Test fitting the ATS in the sump of my Red Sea Reefer 250. Still not sure if I will install it here, but I wanted to see how well it would fit!
The ATS with the hood on for test fitment-
The Nyos 120 skimmer have proven to be a work horse and is still dead silent!
After a Week -
Cleaned and ready to return to service-
GEM5 lights
Currently there is 1 GEM5 light installed in the ATS. I do have all 4 lights and will install them as needed!
Test fitting the ATS in the sump of my Red Sea Reefer 250. Still not sure if I will install it here, but I wanted to see how well it would fit!
The ATS with the hood on for test fitment-
The Nyos 120 skimmer have proven to be a work horse and is still dead silent!
After a Week -
Cleaned and ready to return to service-
Last edited:
pelphrey
New member
Be sure to always do your research when buying fish! I decided I wanted to try a Butterfly fish, the fish was beautiful no doubt. Shortly after introducing the fish into the tank I noticed that my zoa's were closed up. I knew the Butterfly was responsible, I wasn't worried about the zoa's as they are one of my least favorite corals. But when the Butterfly decided to start picking my my scoly and acan's it was time to go!
Luckily for me getting the rock out of the tank is simple. Since I used the Emarco 400 to bond my rock work together to make 2 large structures I removed both structures and trapped the Butterfly!
This seemed like a good time to flip the rocks around. I used to have the large structure on the left, I decided to put it on the right and see how it looked -
Luckily for me getting the rock out of the tank is simple. Since I used the Emarco 400 to bond my rock work together to make 2 large structures I removed both structures and trapped the Butterfly!
This seemed like a good time to flip the rocks around. I used to have the large structure on the left, I decided to put it on the right and see how it looked -
Last edited:
tenurepro
New member
Frag's that I put into the tank over a week ago are doing well!
Can you help me identify this frag? It looked amazing in the display at Aquatic Critter and I had to have it, I did look at the name and as soon as I got home I forgot what it was!
Sps - acropora tenuis if I had to guess... does it large polyps like below
Sent from my iPhone using Tapatalk
pelphrey
New member
Sps - acropora tenuis if I had to guess... does it large polyps like below
Sent from my iPhone using Tapatalk
I've not yet seen any polyps on this frag, nor have I seen it change any colors besides the purple is has always been. I do have it in a location where it is getting a lot of light and moderate flow.
Thanks for your help!
pelphrey
New member
In an effort to take charge or my equipment I picked up this cabinet from Amazon. I initially had plans to keep all of my equipment inside the stand, since I added the Apex things got out of control quickly.
My overall objective is to keep the inside of the tank stand "wet" and move all of the hardware into this cabinet. Doing this I hope will make cable management a lot easier and when it comes time to remove equipment as needed for cleaning it won't be much of a hassle.
I have a little work to do on this cabinet to make it work for me, I hope to have all equipment moved into this cabinet in the next few weeks!
My overall objective is to keep the inside of the tank stand "wet" and move all of the hardware into this cabinet. Doing this I hope will make cable management a lot easier and when it comes time to remove equipment as needed for cleaning it won't be much of a hassle.
I have a little work to do on this cabinet to make it work for me, I hope to have all equipment moved into this cabinet in the next few weeks!
Last edited:
pelphrey
New member
I thought I was going to make it work, but my mind changes daily! haha
How's the nyos going? I pulled the trigger on the reefer 250, and have been looking into a couple skimmers: eshopps s 120, nyos, or classic reef octopus
I love the Nyos skimmer, it is dead silent and is a strong work horse!
pelphrey
New member
Got to work on the "Equipment Cabinet" a little over the weekend. I thought this cabinet came with a wooded back, but it was cardboard. So I cut the bottom off to run cables in!
Added brackets to the stand, this will hold the ply wood going onto the back to screw in equipment as needed -
Plywood added to the back of the cabinet -
Next up will be reserving some time to get all of my equipment moved over. I figure it will take me about 2 hours to be on the safe side.
Added brackets to the stand, this will hold the ply wood going onto the back to screw in equipment as needed -
Plywood added to the back of the cabinet -
Next up will be reserving some time to get all of my equipment moved over. I figure it will take me about 2 hours to be on the safe side.
Last edited:
