n2585722
Well-known member
I think you only press finish. Hit reset value first if you have tried the calibration already that might fix the value displayed. The reset value button is not a part of a normal calibration and is not always needed.
Digital Aquatics Archon Owners Thread
- Thread starter skripo
- Start date
Pickupman66
New member
Yea but don't hold it to time mike. Just watch the reading every few minutes and it is still trending a direction wait. I hit copy a few times (maybe every time I check it) to ensure it don't timeout. Then when it is not trending a direction I move on
janes_mw
Active member
Things working again. Not sure why, but after reloading with fresh flash and re-initializing and reprograming entire system, everything working as advertised now. Just have to play with SL2v2 probe calibrations a little. They seem different (don't change when start is initiated), but not a real problem at the moment.
Entire 300 gallon set up is now switched over. Three power bars, SL1, SL2, DCI (wavemakers), IOE (I/O interface), CaRx control, Skimmer, ATO, Swabbie, T5's, heater, float/level safety, waterbug protection, Salinity monitor, pH monitor, temp (ambient and tank and compensation for SL2). Probably missing something, but basically everything plugged in and running. Alarms/Floats all checked out and functioning good. Email alarms set up as well as remote access via port forwarding.
mike
janes_mw
Active member
Yes, first time i have tried with SL2v2. I will give it a shot tomorrow and let them sit a while. Thanks Danny!
Pickupman66
New member
I need to redo mjne. I'll do it this eve.
So glad to hear it is running now
So glad to hear it is running now
janes_mw
Active member
still getting a false alarm on temp high, can't figure that out, but again, not an issue at the moment. The graphs are stable on the temp that I am using for the high temp alarm and the alarm says 84.5 when the temp shows stable at 78.5.
Pickupman66
New member
What temp. The sl2 or the archon?
janes_mw
Active member
Pickupman66
New member
It seems it is still triggering some alarms. Use your sl2 temp for now for alarming
Pickupman66
New member
We r testing a fix on the false alarms and some other nifty features.
Pickupman66
New member
im just going to drop this right here....
Something Ken Salomon has cooked up for you guys and the Archon. it is pretty slick. How will you use this?
Something Ken Salomon has cooked up for you guys and the Archon. it is pretty slick. How will you use this?
Pickupman66
New member
Good news as well. So far on the update I've had for fixing the false alarms is working
n2585722
Well-known member
The only one I moved over last nignt was the temp alarms. No false alarms on mine last night.
Mike, they removed the reset value button on the input port screen also. I guess they are doing that automatically now when you calibrate the port. I had to recalibrate my SLX ports after the update. All the others were fine.
Mike, they removed the reset value button on the input port screen also. I guess they are doing that automatically now when you calibrate the port. I had to recalibrate my SLX ports after the update. All the others were fine.
Overt
New member
Archon Firmware Update
Archon Firmware Update
So the new update has not worked out well for me.
Once installed the Hardware update accessible on the Systems page doesn't seem to take. Once it is done the Systems page still indicates update available and all the inputs and outputs are not showing
http://i.imgur.com/ZwzQGiJ.png
http://i.imgur.com/BtGaeiR.png
http://i.imgur.com/91JD7iS.png
suggestions?
Thanks 'yall. I'm stuck
Archon Firmware Update
So the new update has not worked out well for me.
Once installed the Hardware update accessible on the Systems page doesn't seem to take. Once it is done the Systems page still indicates update available and all the inputs and outputs are not showing
http://i.imgur.com/ZwzQGiJ.png
http://i.imgur.com/BtGaeiR.png
http://i.imgur.com/91JD7iS.png
suggestions?
Thanks 'yall. I'm stuck
type into the commands section "GetVersions()" then hit "send"
refresh page after a few seconds
janes_mw
Active member
When mine came back with HW version 1.01.1 it was "not good". Happened a few times to me and each time, the unit was bricked..... Not saying that is what happened, but if what Ken says doesn't work, you may need to get with Eric.
mike
n2585722
Well-known member
The hardware update is the one you have to wait around 5 minutes to make sure it completly updates. It sounds like you need to contact DA support and get Eric involved if what Ken has suggested doesn't work. I wait 10 minutes just to make sure before I reset the controller.
Did you refresh the page? It always says that....because the command has no data to return, it just resyncs things on the backend
Similar threads
