how to add feed for reverse osmosis

StrategicReef

New member
I have regular shut off valve under the kitchen sink I was wondering how I could add the RODI to it.

I see there is some adapters available to install either on the faucet or shut off valve side but I don't know which to get. I think the shutoff valve has 3/8" compression output.

I don't want to use the pierce valve or replace the shutoff at this point..


Maybe something like

http://www.plumbingsupply.com/quick-tee-adapter.html


but are these available without ordering online?

Is this the same thing from home depot?

http://www.homedepot.com/h_d1/N-25e...d=-1&keyword=brasscraft+fitting&storeId=10051


Thanks
 
Last edited:
Funny, I had to use the T-adapter today. The bonehead plumber didn't leave me enough room to use the TAP adapter.

I used the tee adapter and a 1/4 compression nut w/Insert part#17000004. I had to cut the flared insert to about 3/8 inch. It originally was way too long for the nut to reach the 1/4 thread of the tee adapter.

It was a pain to cut the little brass insert. I place a large nail inside the insert and cut around the nail. I was scared i was going to bend the brass and have to buy another one.

Worked perfectly.
 
Welcome to the joy of plumbing! Now you know why the plumbers' trucks have a thousand little bins with different connectors and adapters in them!

An adapter like you linked to should work, but it depends on what size fittings you have. Check the size of the faucet supply line, or shut off the supply and take the whole thing with you to the hardware store, along with the adaptor you have for your RO/DI setup.

Home Depot and Lowes carry 1/4" murlock fittings, similar to these], so you might be able to find something like it there.
 
Funny, I had to use the T-adapter today. The bonehead plumber didn't leave me enough room to use the TAP adapter.

I used the tee adapter and a 1/4 compression nut w/Insert part#17000004. I had to cut the flared insert to about 3/8 inch. It originally was way too long for the nut to reach the 1/4 thread of the tee adapter.

It was a pain to cut the little brass insert. I place a large nail inside the insert and cut around the nail. I was scared i was going to bend the brass and have to buy another one.

Worked perfectly.

Your doing something wrong or the parts was not right for the application? You shouldn't have to cut anything. The Photo below part will work every time. (Don't use any brass sleeve on plastic line)
 

Attachments

  • Watts.jpg
    Watts.jpg
    52.4 KB · Views: 5
Your doing something wrong or the parts was not right for the application? You shouldn't have to cut anything. The Photo below part will work every time. (Don't use any brass sleeve on plastic line)

Manufacturers Notes:
PRODUCT DESCRIPTION

This plastic compression sleeve is ideal for use with copper, brass, aluminum, or plastic tubing on gasoline, grease, oil, water, vacuum and air lines. It is not recommended for use with steel tubing. This compression sleeve is easy to use for both contractors and the do-it-yourselfer. Not for underground use.

Ideal for use with copper, brass, aluminum or plastic tubing on gasoline, grease, oil, water, vacuum and air lines
Use with brass insert when using plastic tubing (brass insert is included)
Not recommended for use with steel tubing
MFG Brand Name : Watts MFG Model # : A-8
MFG Part # : 17000008

I am confused by your response. You say not to use the brass sleeve on any plastic line. Your picture on the part to get has a brass sleeve and your next post is a brass valve???

Are you saying to only use the plastic compression sleeve?

I know that using a brass anything on RO water specifically will eventually deteriate the brass, but this is the main input.
 
Manufacturers Notes:
PRODUCT DESCRIPTION

This plastic compression sleeve is ideal for use with copper, brass, aluminum, or plastic tubing on gasoline, grease, oil, water, vacuum and air lines. It is not recommended for use with steel tubing. This compression sleeve is easy to use for both contractors and the do-it-yourselfer. Not for underground use.

Ideal for use with copper, brass, aluminum or plastic tubing on gasoline, grease, oil, water, vacuum and air lines
Use with brass insert when using plastic tubing (brass insert is included)
Not recommended for use with steel tubing
MFG Brand Name : Watts MFG Model # : A-8
MFG Part # : 17000008

I am confused by your response. You say not to use the brass sleeve on any plastic line. Your picture on the part to get has a brass sleeve and your next post is a brass valve???

Are you saying to only use the plastic compression sleeve?

I know that using a brass anything on RO water specifically will eventually deteriate the brass, but this is the main input.

Yes, "not to use the brass sleeve on any plastic line". "picture on the part to get has a brass sleeve" it did not show a brass sleeve, fact is you did not see the sleeve is not brass but a 'Delrin' sleeve (plastic) and the insert, is brass.
'Sleeves' AKA ferrules, would be the part that makes the compreshion around the tubing and the insert is what keeps the tubing from collapsing in under compreshion on plastic line only as I'm sure you know. Brass sleeves AKA ferrules can and often cut into the plastic line especially if the line is wiggled a lot (lets say you installed a inline valve and the line is often moved) The part in my post is used for plastic line and is correct.

http://www.watts.com/pages/_products_details.asp?pid=6397
Aloha,
brahda:wavehand:
 
In case anyone is interested, this is the RIGHT part for the job.

Funny, I had to use the T-adapter today. The bonehead plumber didn't leave me enough room to use the TAP adapter.

I used the tee adapter and a 1/4 compression nut w/Insert part#17000004. I had to cut the flared insert to about 3/8 inch. It originally was way too long for the nut to reach the 1/4 thread of the tee adapter.

It was a pain to cut the little brass insert. I place a large nail inside the insert and cut around the nail. I was scared i was going to bend the brass and have to buy another one.

Worked perfectly.

Now I see why you had problems:wavehand:
 
Back
Top