Is 7095 broken ??

[IS]

Rvitko,
After my two 6200 were broken. I found out 7095 also broken today. How lucky am I ? I set the power between 80 to 100 but LED show 30 - 80 level. It can't reach to 100 %. I change to each funtion but still can not Can I check by myself or I need to sent it to your company again. Thank you
Ben

 

[rvitko]

What pumps are you running on the 7095? Are they clean? Three things can cause this, the pumps are dirty or not getting enough power (this is mainly possible with 6000 if mains voltage is below 110V), or the resistance in the board is too high, some older units had this problem but it should have shown up when new. In this case the pumps go to 100% but the lights only light up to 80%, it is the lights on the controller that have too much resistance but this only was an issue with a few of the very first ones from the end of 2004.

 

[IS]

Rvitko,
I do have one 6100 and one 6000 pump in my hand but I only use 6100 to work with 7095. I also found out is not pump problem. I put 6100 in channel 2 but LED only reach 80 %. When I changed it to channel 1. It can reach 100 %. Looks fine so I guess something wrong in 7095. What do you think? Thank you
BEN

 

[rvitko]

It is just the LED that is the problem, the pump is still reaching 100%. If you can solder I can send a circuit board to a relative in USA who can forward it to you. You will need to desolder and resolder the photocell/LED. I normally would not do this but i understand the transport cost is very high for you.

 

[IS]

vitko,
My relative will go to USA next month. I will ask her sent it to your shop. I guess it might stay in your shop for a while. I need to save some money and I will let you know when I need it back. Is it okay for you? By the way. I will have my two pumps back next few days. I hope it can work well after you fix it. Thank you for your help.
Ben

 

[rvitko]

I can repair them quickly, if I have to hold it for a while it is no problem, just include a note in the box.

 

[IS]

rvitko,
My relative will go back state 16 December. My freind's friend will come back before 25 December. Is it enough time for you to replace. Thank you.
BEN

 

[rvitko]

Yes, if they send it right away, I can return it in time.

 

[IS]

vitko,
My relative went back USA yesterday. You will have my 7095 as soon as possible. Please help me to solve the problem. Thank you
Ben

 

[IS]

vitko,
Have you receive my 7095 yet? Thank you.
Ben

 

[rvitko]

It arrived today. I will have it ready to ship by tomorrow.

 

[IS]

Thank you vitko. Great service.
Ben

 

[rvitko]

It is finished I believe. You mentioned in the letter that the moonlight was broken? I found no problems, was I missing something? I changed the circuit board.

 

[IS]

vitko,
I am not sure about moonlight problem. Sometimes it didn't work well. If you can change it. That will be great. Thank you
Ben

 

[crumbletop]

<a href=showthread.php?s=&postid=9051016#post9051016 target=_blank>Originally posted</a> by IS
vitko,
I am not sure about moonlight problem. Sometimes it didn't work well. If you can change it. That will be great. Thank you
Ben

Regarding the moonlight, at first I thought mine had a problem (and perhaps it does), because it didn't turn on with the same intensity each time. Then I noticed it would change its intensity over time and figured that is part of the moonlight program. So I never looked into it further. Perhaps that is what you are referring to.

 

[rvitko]

Yes, it brightens and dims through a 29 day lunar cycle. Ben, I already returned it to Marine Depot to be sent on to you. We sent it out Friday.

 

[IS]

Okay. Thank you Vitko and crumbletop.
Ben