Jbj ato

reefdiction

New member
I just bought a used JBJ ato to use as a topp off. I am reching out here to find out what pump are you guys using with this set up?
 
That tom's aqualifter used mine for vacation for five weeks with no faults what so ever, even had someone checking the tank for me who complained about being bored.
 
aqualifter pump. can anyone post pics on how they run their pumps. please Im setting my jbj ato up too. :wavehand:
 
I have been using the JBL ATO for over 3 years without a problem. My RO reservoir is only 3 gallons so even if something did fail, it would not drop my salinity levels to dangerous levels. I use the Mini 404 as well. I have the level set with the float to just above the pump to protect it from running dry.

ato.jpg
 
Make sure to put it on a timer that cycles power to it a few times a day, those things have a habit of locking up....reseting the power fixes it.

Additionally, there are some internal settings you can manipulate for alarms and pump timing. The manual can be downloaded from the JBJ website.
 
Make sure to put it on a timer that cycles power to it a few times a day, those things have a habit of locking up....reseting the power fixes it.

Additionally, there are some internal settings you can manipulate for alarms and pump timing. The manual can be downloaded from the JBJ website.

I have seen this posted a couple of times now but for the life of me I cannot find how to increase pump times anywhere, even on their site. Can you point me there or tell me how?

As for setting it up on a timer? Yours must be defective as mine has been running for 15 months without the slightest hiccup.
 
Last edited:
I have been using a JBJ for approx 3 yrs and it has worked flawless.

I use a cheap and small Rio pump.

I also have a ~ 3gal ATO reservoir so even if a float stuck it wouldnt do much harm. I do have to refill every 4 days but I check the sump almost daily so no biggie. When I go on Vac I have a friend stop in every 3 days to feed and fill the top off.

SumpATO.jpg

Sump12132009.jpg

PumpONOFF.jpg
 
I have seen this posted a couple of times now but for the life of me I cannot find how to increase pump times anywhere, even on their site. Can you point me there or tell me how?

As for setting it up on a timer? Yours must be defective as mine has been running for 15 months without the slightest hiccup.

http://www.jbjlighting.com/pdfs/ATO_ht_adjust_float.pdf

http://www.jbjlighting.com/pdfs/ATO_ht_remove_speaker_buzzer.pdf

It was defective, no doubt about that, it ran great for a year or two, it was after that it started to get a little squirrly. Do a few searches, I wasn't the only one it happened to.
 
Thanks for the link. I have searched and most issues were with bad or dirty floats or people not understanding the 3 min cutoff. As an example, you have a large sump and use an aqualifter which pumps very little water. 3 mins may not be enough time and it will shut down before the sump has reached it,s level and consequently will not start up again since the float is already down. I have seen posts where others have corrected the problem by installing larger pumps not knowing all they had to do was to increase the failsafe pump time as shown in the link you just posted.

FYI. JBJ ATO is on special at Aquacave for $79. :fun2: http://www.aquacave.com/jbj-ato-automatic-top-off-brsystem-water-level-brcontroller-1935.html
 
Last edited:
I have been using a JBJ for approx 3 yrs and it has worked flawless.

I use a cheap and small Rio pump.

I also have a ~ 3gal ATO reservoir so even if a float stuck it wouldnt do much harm. I do have to refill every 4 days but I check the sump almost daily so no biggie. When I go on Vac I have a friend stop in every 3 days to feed and fill the top off.

SumpATO.jpg

Sump12132009.jpg

PumpONOFF.jpg

Clean set up! :beer:
 
Went to Install the float brackets and realized that they did not come with extension. Another delay in installation. Got to figure out something ti extend these brackest.
 
Back
Top