Looking for a good deal on a skimmer

[wareagle35031]

I am replacing a crappy sea clone skimmer if anyone has one they would like to sell or know of any bargins out there.

 

[thewashcaps]

I have a corallife super skimmer for 65 gallon only 4 months old had to get bigger one got a 150 gallon tank now pm if intresested

 

[The0wn4g3]

is you're seaclone in-sump or HOB? If it's in-sump you can do some easy mods and make it much much better.

 

[wareagle35031]

its hob but I could put it in my sump

 

[jrthomas40]

i tried to mod a seaclone i had once and ended up breaking it...tried to make the inner tube shorter to give more bubble reaction time ended up breaking the black plate that holds the inner tube

 

[wareagle35031]

<a href=showthread.php?s=&postid=13158003#post13158003 target=_blank>Originally posted</a> by The0wn4g3
is you're seaclone in-sump or HOB? If it's in-sump you can do some easy mods and make it much much better.

Like what?

 

[JR's Reef]

This may help
http://reefcentral.com/forums/showthread.php?s=&threadid=497630

 

[TOYTEK]

Also try this thread
http://reefcentral.com/forums/showthread.php?s=&threadid=1293886
The needle wheel mod worked best for me, shortening the inner riser tube only seemed to increase the amount of bubbles in the tank.

 

[fishman122]

i've got a aqua c remora pro over on ebay right now, only a day left and the bid is only at $11

 

[The0wn4g3]

First, you remove the center tube, it's useless. Remove any tubing for use as a HOB. Take the pump (I'm assuming it's a maxi-jet) and sand off the 2 little nobs on the venturi piece. Reverse it and jam it into the intake of the maxi-jet. Attach the maxi-jet directly to the reaction chamber intake. After the mods, the air is chopped by the skimmer, and there's no tube so the reaction chamber is essentially larger. I'm not at home so i can take photos to help explain, but hopefully that makes sense. It's louder, but it performs much, much, better.

 

[wareagle35031]

<a href=showthread.php?s=&postid=13174403#post13174403 target=_blank>Originally posted</a> by The0wn4g3
First, you remove the center tube, it's useless. Remove any tubing for use as a HOB. Take the pump (I'm assuming it's a maxi-jet) and sand off the 2 little nobs on the venturi piece. Reverse it and jam it into the intake of the maxi-jet. Attach the maxi-jet directly to the reaction chamber intake. After the mods, the air is chopped by the skimmer, and there's no tube so the reaction chamber is essentially larger. I'm not at home so i can take photos to help explain, but hopefully that makes sense. It's louder, but it performs much, much, better.

I did the bio ball mod to the pump, it works better, it is pulling dark sludge now, just not much of it, it takes a long time for it to reach the collection cup, which I also cut down. Are you telling me to cut the tube which causes the tornado effect, and if so how? I cant get to it, its way down in there, and mine is the newer style and wont come apart.

 

[The0wn4g3]

Yea, it's best to cut out the inner tube. I'm not sure how you can do it with the new style, but on the old one you could wiggle the large inner tube that floats to remove it. Then just reach down with a pair of pliers and break it out as close to the bottom as possible.
In reality, the tornado effect does more hard than good. without it you should get more bubbles and longer contact time which should produce more waste.