Skimmer overflowing

anthonys51

anthonys51

New member
I used the brs putty only 2 ounces. Made my whole tank smell and skimmer has be overflowing since Sunday. Anyone else have this experience and what did you do to stop it


Sent from my iPhone using Tapatalk
 
I had this for a month. My situation was a bit different as I had a new tank, new skimmer and little life/corals in my tank.

I was recommended to do a 50% water change and place a plastic bag over the skimmer so the tiny bubbles stopped making a salt mess.
Hopefully it will be a shorter issue with your situation.
 
Yours lasted for 3 a month You have got to be joking. It was a 2 ounce piece I have 620 gallons of water. Pretty hard to do 50 percent water change


Sent from my iPhone using Tapatalk
 
I used instant ocean putty for the past 7 years and never experience skimmer over flow because of it. I recalled that I used a whole stick once too. perhaps, my skimmer is not that sensitive.
Maybe your skimmer's venturi valve happen to coincidentally clogged while you are using the putty? Worth checking the pump. Most I heard was only a few hours - half a day of over flow after using putty and should be back to normal after whatever in the putty that causes the skimmer to go nut.
 
flooddc said:
I used instant ocean putty for the past 7 years and never experience skimmer over flow because of it. I recalled that I used a whole stick once too. perhaps, my skimmer is not that sensitive.
Maybe your skimmer's venturi valve happen to coincidentally clogged while you are using the putty? Worth checking the pump. Most I heard was only a few hours - half a day of over flow after using putty and should be back to normal after whatever in the putty that causes the skimmer to go nut.
Click to expand...



Yes I never heard if this long. But the putty did make my basement smell like burnt something and I didn't even use it in those tanks. Used it upstairs


Sent from my iPhone using Tapatalk
 
anthonys51 said:
Yes I never heard if this long. But the putty did make my basement smell like burnt something and I didn't even use it in those tanks. Used it upstairs


Sent from my iPhone using Tapatalk
Click to expand...
they do smell and stick to your fingers for quite long. this I know for sure :)
 
I used the one that came in brs frag pack. I used them before never had this happen. This one was also very wet.


Sent from my iPhone using Tapatalk
 
Sorry typing on my phone. autocorrect

Do I just wipe it down to clean or should I soak it


Sent from my iPhone using Tapatalk
 
anthonys51 said:
Sorry typing on my phone. autocorrect

Do I just wipe it down to clean or should I soak it
Click to expand...

No excuses :p

Give it a thorough cleaning and put it back.. I don't know what skimmer you have so I don't know if you can easily access the inside to wipe down all surfaces,etc.. if not a soaking may be in order.
 
I Have the nyos quantum 220 skimmer. So Yes I can easily access inside of it. It's pretty big skimmer, so soaking it will be a pain in the butt. So Will try to wipe it first.


Sent from my iPhone using Tapatalk
 
I just used some of the putty to secure some frags and my skimmer always overflows for a day or so after I use it. Just open the valve a little on the skimmer until it stops overflowing and then adjust again the following day to resume normal skimming.

And yes it smells like burnt hair. . . Usually just when mixing it though
 
I have used whole sticks at a time of JB Waterweld and never had this issue.

I would clean the skimmer well and see if that helps.
 
I did. Problem now is I can't get the skimmer to go back. I can get If to overflow but can't get it to bubble. Or I can get it to bubble but it overflows. Also bubbles come out of the bottom this way too. Will ask my lfs guy to cone check it out. I am good with fish and corals. Not so good with the eauipment


Sent from my iPhone using Tapatalk
 
Just an update. After 7 days it finally just fixed itself. Very strange maybe the putty was a bad batch. It was more oily then usual the putty. Well all back to normal. My nitrates did go from 2ppm to 10ppm In a week but it could of been worse


Sent from my iPhone using Tapatalk
 
I stopped using that putty cause it always made my skimmer go nuts. I now use Water Weld. It is the same company that makes JB Weld and I get it at home depot/lowes. ITs great stuff and doesn't make my skimmer go nuts.
 
You must log in or register to reply here.

Similar threads

A
OVERFLOW BOX HOLE?
Replies
9
Views
855
allenford6
A
E
Red Sea weir overflow
Replies
9
Views
118
griss
griss
J
Plumbing 300 gallon acrylic aquarium
Replies
4
Views
3K
corvinridge
C
A
DRILL aquarium only 1 DownPipe?
Replies
0
Views
234
Andrés Garza
A
T
I'm confused...
Replies
12
Views
505
wvned
wvned
Back
Top