Tunze 7096 night mode

rogerrgr

rogerrgr

Member
I have a 7096 controller and 2 x 6105's set on 1 minute interval 40-90 pulse. When they kick into night mode they each run at 1 minute intervals while the other is completely shut off. Is that what they are supposed to do on that mode? Or is there a way to program them not to shut off completely on night mode? Thanks!
 
Mindflux said:
Roger is out right now for a couple days. I am not a Tunze employee but I'll try to help.

Can you tell me which ports you have your 6105's plugged into? I believe night mode only affects Ports #3 and #4. (it shuts them off if you have night mode enabled, I believe).

http://www.tunze.com/fileadmin/images/product_additional/7096.000#02#534.pdf product manual.


This may only apply to ports 3 and 4 if you have the wavecontroller option enabled.
Click to expand...

I have them on ports 1 and 3. I was under the assumption that 1 and 3 worked together, and 2 and 4 worked together on the interval mode. The wave controller option is not selected, only the interval mode and night mode. They run on 1 minute intervals on night mode, one off while the other is on low speed.
 
Pg 73 of the manual suggests this:
(2) Simulation of tidal currents (“Interval”)
The pump channels 1 and 2 are switched on or off alternately. The water flows through the reef from both
sides at an adjustable switching time from 1 minute up to 12 hours.


I'd try putting the pump plugged into #3 into #2 and program port #2 accordingly and test night mode.

Sometimes the translations get muddled in the manuals. I hope this helps you, if not I'm sure Roger can clear up any misconceptions I have.
 
qf3qnl.jpg



The alternating flow with the picture of Saturn (?) above it seems to be the "key" for Interval according to pages 72 and 73.
 
Plugged into #1 and #2 didn't work on the interval mode, but did work on night mode.
Just realized that interval mode is supposed to be channel one on for set interval then turn off..
Then channel 2 on for the interval while channel 1 is off and so on.

My biggest reason I was having troubles with one being off for a period of time, night mode and interval mode, is that sometimes my one 6105 doesn't start back up on its own without me manually pushing on the prop.
I will try taking it back apart and recleaning it again I guess, then hopefully problem solved! It's hard to get all the calcium off inside the prop housing and vinegar solution doesn't work that well for me on the hard crusty stuff.. Definately going to do more frequent cleanings!

I'll post an update, thanks!! These pumps are amazing and worth every penny!!
 
I'm surprised you aren't having luck with intervals in slots 1 and 2. And it appears my assertions about slots 3 and 4 being affected by night mode are correct. Though I thought primarily things got turned off completely only if it was in "wavebox" mode on slots 3&4 and anything on 1&2 should just run at decreased power.
 
Yes, when I hooked them up into 1 and 2 they did decrease and increase power, but both at the same time same power ramping levels and never shut completely off.. I have them at opposite sides of the tank and they are fighting each other in the middle of the tank causing a huge churning wave when on slots 1 and 2..
I wish I had a laptop and didn't have to keep unplugging it to change stuff!!
 
rvitko said:
Please double check that your program uploaded properly to the controller. Interval should run 1 and 3 at the same time and 2 and 4 at the same time.
Click to expand...

I found this in another thread. I'm not sure if that means 1 and 3 are on the same interval or opposing intervals.
 
Aren't you still having night mode issues with the one connected to port 3?

*Edit: AH! I get ya.

I did see in a thread Roger said the next program update will allow the 'off' pump to idle at a certain speed while it's not the actively pulsing pump. Hopefully that'll come along with the 3 new modes promised before long.
 
Mindflux said:
Aren't you still having night mode issues with the one connected to port 3?

*Edit: AH! I get ya.

I did see in a thread Roger said the next program update will allow the 'off' pump to idle at a certain speed while it's not the actively pulsing pump. Hopefully that'll come along with the 3 new modes promised before long.
Click to expand...

Yup, that is what I was hoping it would do on that mode. Just saw that there is supposed to be an update this week, maybe! It would be nice to have the off pump at that time run at an idle speed instead of being off.. Either way, after adding my second 6105 on the other side of the tank, they are stirring up some stuff off the rocks and making my sps polyps sway nicely!
 
I just found it, copied the link and came here to paste it, and you already found out about it! Downloading it after I get off work to try it out. Thanks!!
 
The update will solve this problem with the idle speed turned on. It was working normally. Thanks!
 
You must log in or register to reply here.

Similar threads

Guygettnby
If not for bad luck...
2
Replies
21
Views
1K
leebca
L
PI Guy
tunze multi-controller question
Replies
2
Views
341
Jposch
J
B
55 gallon Tank Soft coral and fish under regular LED light
2
Replies
24
Views
2K
Misled
Misled
A
Clownfish Mating? Fighting?
Replies
2
Views
667
griss
griss
Brian60077
Be patient, wait, and do not rush to add things ???
Replies
11
Views
793
Brian60077
Brian60077
Back
Top