WTB mesh for mesh mod

Schplitter

Schplitter

New member
Hi guys,

As you all know I'm building that monster skimmer. I picked up 3 rio 1700 from Planet Reef tonight and need to mesh mod them.

Does anyone have about 10"X10" of the stuff I could buy.

Thank you,

BK
 
I have some that you can have for the mere price of 2 BB from McDonalds, I prefer hot and not mild sauce. I do not like their drinks so OJ is not needed. I am around Sat AM and I live right by Wash U and the Loop.
PL
 
Not that I do not want BB-but what is your reason for skimming so much, if at all?? just curious
 
Don't want to undercut prices...

I have a couple of different kinds. Enkamat 7010, 5006, 7220, 7020. For larger pumps the heavier 7220 might work better.

Have you experimented much with the mesh mods? I did a bit and found less to be better than more. My first few tries were not so good when I mashed 3 or 4 layers together. I had much better success with just 2 layers more loosely packed. This made more bubbles and now the pump starts every time.

I did the Sedra 3500 pump that was JXMETAL'S

Faz
 
Mesh

Mesh

Hi. I have virtually unlimited mesh from an old roll of DLS filter material from years ago. You can have as much as you want. I'll be at the meeting tomorrow night if you want some then.
Bruce
 
geoxman: U like that McDonalds breakfast lol. If I buy yu 4 can I go fragging in your tank hahah. I should be free Saturday.

The reason I want to skimm so much is because I have issues. lol. That's true but the main reason is the sps thing and my addiction to large fish. I would hate to havea100 gal 6ft tank with 2 2"fish in it. I'm trying the impossible: Keepng large healthy well fed fish and lots of health coral...

fazgood: I tried it once on my Euro Reef and hated it because I did not understand it...I'm always open to do some testing... If you have some le over I have 3 pumps and I culd try 3 different materials at the same time to see what works best...

bprice:
I'll be at work tommrow from dawn to well after dusk so I can't make it to th meeting but we can meet up some place else if you have time.

Thanks to everyone. I should have enough mesh to do testing and then some.

Thank you,

BK
 
What area are you in?

A couple of things I learned in the process.

Measure the power consumption before and after

When modifying the existing impeller, take care to drill holes for the wire ties at geometric intervals

Don't use too much, you are not looking for a dense mat, you want water to flow through with bubbles so the mesh can fragment them

Test it before you put it all back together... several times. Make sure the pump starts both when its cold and after it warms up

Use heat to trim the edges

Faz
 
The reason I want to skimm so much is because I have issues. lol. That's true but the main reason is the sps thing and my addiction to large fish. I would hate to havea100 gal 6ft tank with 2 2"fish in it. I'm trying the impossible: Keepng large healthy well fed fish and lots of health coral...
Click to expand...

I agree with you here are some images from my tank. I have 10 fish in my tank 2 are large and emp and a naso. All the corals in my tank are really starting to take off and I feed the fish daily. The only coral that looks off in the tank is that one that is still not fully recovered from the two power outages of 06. It is slowly re-encrusting the bottom of the coral, if you look at it from the top you would not realize it was ever damaged. It is purple with green polyps.

My Tank
 
fazgood: i'm close to gateway aquatics. Forder and Lemay intersection...

I will have to do something different because these impellers do not have a plate but have the regular fins like you would find on a mag drive... I was thinking about cutting off 3 of the fins and keeping the other 3 then trimming the leftover 3 down so that they are only 1/8 instead 1/4". Then put one layer of mesh on each side...

beapeams:

Your tank looks awesome. How loud is that gen-x 6000. I still have time to return these pumps and go with one gen-x 6000 like they use on the Euro Reef rs-250. I wanted to do this originally but people told me that the pump is way too loud...
 
The return gen-x I don't hear at all. The gen-x 6000 on my skimmer is the one that makes noise. It would be to loud if it was in my living room, but my fish tank is in my basement and the equipment is in its own room.
 
This would be under my tank in the dining room right next to the living room. Ok so I'll go with the recirc thing I guess...

Thank you
 
Gottcha.

Another Note, if you do have that tubing let me know what you want for it. I can meet you at beldts tonight if you are going to Pizza night.

Sean
 
You must log in or register to reply here.

Similar threads

R
some random questions
Replies
0
Views
49
redseaapples
R
R
15G Nano Reef Help
Replies
13
Views
2K
kharmaguru
kharmaguru
Easygoing1
PFO Aquatics SOLARIS Rebuild And Questions
Replies
8
Views
2K
oreo57
oreo57
tidepoolinkansas
Looking for ongoing advice.
Replies
11
Views
1K
JohnL
JohnL
C
Scored a complete setup for $100
Replies
13
Views
2K
griss
griss
Back
Top