n2585722
Well-known member
I don't think it uses the 100ths digit on the temp but to get it on pH all the readbacks on the probe ports have the 100ths digit even ORP has it now but it is always 0.
Digital Aquatics Archon Owners Thread
- Thread starter skripo
- Start date
SoloGarth
Active member
I have to disagree. Mine at least is not stable. I am having ongoing issues with the clock which makes the timers malfunction. I thought this had been fixed but it happened again on Friday. In addition to this I am not able to change the username and password without physically removing the flash drive and editing the file on my computer.
Also today the Archon lost connectivity. I had to do a full reset to get it to reconnect to my network. I have to go to Austin for work on Sunday for a week. I am more than a little worried leaving this.
janes_mw
Active member
I have to agree. I have exactly same behavior as Solo...
I am back running my RKE wityArchon running on the counter with temp probe and a PC4 with just "stuff" hooked to draw power and exercise the unit. I don't see moving it back until i see 30 days of consistent behavior
n2585722
Well-known member
I just checked mine the clock is dead on. I have the UTC at -6 and daylight savings time unchecked. This seems to give me the correct time.
Is that Austin Texas? If so i live just outside of Austin.
SoloGarth
Active member
Oh nice. Yeah Austin TX. I haven't been down for years but that is where the company I work for is based.
I cannot get the system to save my username and password. I think that when I updated it manually it may have screwed up the time zone again? Is there somewhere in the code to manually set the time zone? I thought this issue was resolved but it was not. What are the software firmware versions you are using?
SoloGarth
Active member
Oh ok. I think only the people with 1.08.7 are having this problem.
My company is called Active Power. Flywheel powered UPS systems.
SoloGarth
Active member
Ahh I see. Well scratch that I guess. I have been watching the system all today but it has been behaving itself. I would much prefer it to be constant in failure than intermittent.
n2585722
Well-known member
My understanding is that 8.07 is 8.05. It was 8.06 that had an issue. I think Dave and Ken have 8.07. I may be the only one left with 8.05. I never updated to 8.06 before it was pulled so I had no need to update to 8.07.
I am not sure if 9.24 has been released yet but the only difference is the 100 ths digit on the readbacks.
I think we may have some of the flywheel things where I work at Freescale.
I am not sure if 9.24 has been released yet but the only difference is the 100 ths digit on the readbacks.
I think we may have some of the flywheel things where I work at Freescale.
Pickupman66
New member
I am on 8.05. One thing you may want to do is check the system time thru telnet. If it is not what you need then use a different utc. That's what I did and use -5 utc. DST is unchecked and I'm on central time and its perfect.
Pickupman66
New member
Oh yea. To do so run telnet and at the prompt simply type date. It will show your system time.
SoloGarth
Active member
SoloGarth
Active member
n2585722
Well-known member
I am in the implant maintenance group.
SoloGarth
Active member
Oh ok. Yeah Texas isn't my area so I am not very familiar with Freescale. I just recognize the name.
n2585722
Well-known member
If you goto the command prompt in windows type telnet. Once in telnet use open with the IP address.
Example: open 192.168.1.118
This will get you the prompt
DigitalAquatics Archon System
Root@DigitalAquatics /#
Type in date. You should get the date back as a response.
I think you type exit to get out.
Example: open 192.168.1.118
This will get you the prompt
DigitalAquatics Archon System
Root@DigitalAquatics /#
Type in date. You should get the date back as a response.
I think you type exit to get out.
n2585722
Well-known member
That is interesting. I didn't change the password. I did back in December without an issue but since I have just left it at the default.
Similar threads
