Digital Aquatics Archon Owners Thread

Firefox is usually good. I use Safari on my iPad instead. When you type in 192.168.10.1 in the browser you should get the name and password entry on you screen. if you have not changed it it should be DigitalAquatics for the name and password for the password. I am guessing you do not get the pop-up to do that. Have you tried a different browser?
 
Yeah, I don't get a pop-up at all for it. It either just says connection timed out or something like cannot load the page. I tried it once with chrome and got the same result. I can try my roommates Mac tomorrow, but past that I have no clue?
 
When you hook up a wired connection can you get to the setup page? If so does it show a wireless IP address? Have you setup the wireless settings on the setup page? You can leave it hooked up wired and still try the wireless since both will work at the same time.
 
Also it will not show the settings after you save them. They default back to blank. So you cannot go back a see the wireless settings to see what they are. Sorry I did not mention that before.
 
Below is a screen shot of the setup page showing the IP addresses on the right. Ethernet IP is the wired IP address, Wireless IP is the wireless IP address through your wireless network and Archon IP is the IP to use when connnected via the Archon wireless network. Since I do not have a wired connection my Ethernet IP is blank here. The Archon IP can be changed using update Archon conection. The wireless IP is aquired from your router. Hope this helps.

IMG_1450_zpsabthp7qx.png
 
Yes, I'm​ able to get to all of the pages including setup. From everything I see I can do all the programming and everything else.

If I enter the wireless settings then hit save the page doesn't do anything for a moment then goes to a cannot connect screen. If I refresh the page it'll all load again. The page does show the wireless IP address, the 192.168.10.1 address.

If it is connected to Ethernet I've noticed the Archon does not show up on my wifi list. If I pull the cord, type in 192.168.10.1 it just gives me the cannot connect page.
 
Thanks for the screenshot. I have the wireless IP, however I have not seen the Archon IP, it stays blank. I'm away from my Archon and computer at the moment, tomorrow I might be able to record or screenshot what I'm seeing
 
On my iPad when I try and connect to the Archon wireless and it does not show up I will type the archon name in. It says it cannot find it, but then it shows up as a selection after that. Under Update Archon Connection see what the Access Point Address is. This should be the address that shows up as Archon IP. If Archon IP is blank that may be why you don't get anything through the Archon network. I don't think you router is going to issue 192.168.10.1 as an address. That is usually reserved for a router itself.
 
Hey, sorry didn't get a chance to tackle it yet. Next chance I'll have is tomorrow evening. That said I did finally get the new one from Eric. At this point I'm curious what my issue with the old one is, so tomorrow night I'll give it one last go to get it connected since I've made some progress, if no luck I'll get the new one setup. Eric said it was fully updated so it should be a matter of just connecting it to the network. I'll post an update when I get a chance to play around with them tomorrow. Thanks for following up!
 
I got the new Archon connected to my network tonight without issue, as well as setting up port forwarding on the new one. So not sure what the issue was with the old one still but at this point I'm calling it quits on messing with it. I'll start connecting modules and probes to it tomorrow, hopefully there aren't any more issue in my future.

Thanks for the help!
 
Sounds great. It may be an issue in the Linux side of the programming or some script file did not update correctly. The main thing you are up and running. Eric can check out the old one to find out the cause when he gets it back.
 
I have an issue with the wired IP address not showing up in the setup page. A few days ago I came home to find the system shut down for some reason. I was not able to log into the Archon through my home network or remote access so I pulled the power and the bus connections and after a period of time plugged them in again. After that the unit powered all of the outputs and inputs but the only way I can see the Archon is wirelessly. I noted that the green light on the Archon is not lit. Do I do a shutdown and reboot the system to reset it and then will it give me the Ethernet IP? If not what can I do to restore it? Thanks.
 
Are you sure it's not a cable issue? Try resetting it at the Archon and your router.if wireless works and the Archon hot spot is working then the webserver is working. It is doing as it's programmed?
 
My SL1 is causing my archon to continually reboot. All I use that module for is the switch inputs. Is it an IOE module to replace for switch functionality?
 
You must log in or register to reply here.

Similar threads

scuzy
FS: complete setup
Replies
3
Views
1K
ashburn
A
S
Help with Overflow Design Issue
Replies
0
Views
183
SFMAquariums
S
E
What's Old is New Again
Replies
2
Views
498
Uncle99
Uncle99
BigEZ77
Urgent Help Requested - Wrasses Won't Come Out - CB Blue Tang Arriving Today (NO QT)
Replies
8
Views
839
rrrrob
rrrrob
F
New Reef - Need recommendations
Replies
13
Views
2K
Cdentata
C
Back
Top