mnml's rimless

[mnml]

After many months of planning and waiting, I've finally got my new tank set up. It's still a work in progress but I'd thought I share some pics.

Tanks: LeeMar rimless starphire, all 4 sides. 48" x 30" x 20", 1.5" drain, 3/4" return
Stand: Custom built pine wood, 42" tall.
Sump: Advanced Acrylic, 30" x 20" x 16"
Lighting: ATI PowerModule 8x54w
Skimmer: ATB 840 v1.5
Carbon Reactor: Warner Marine MR-100
Dosing Pumps: BRS dosers, 1.1 ml/min
Controller: APEX Neptune
Return: Eheim 1260 or Tunze Silence (still need to test)
Circulation: Vortech MP40w gen2 x 2
ATO: Tunze Osmolator
Rocks: Marco rocks
Substrate: Tropic Eden reef-flakes 4mm
Salt: Tropic Marine

I still need to get the plumbing done and hang the lights but here are some pics so far.

 

[Bonta]

oO !! Shiiiiny !

 

[robojet]

SWEET!!! Can't wait to see the progress!!!

 

[uhuru]

Very nice. Where did you get the square tubing for the light hanger? I like it better than the round bent tubing that you commonly see.

 

[d-man]

looks very clean, can't wait to see the finished work

 

[mnml]

Thanks everyone!

Very nice. Where did you get the square tubing for the light hanger? I like it better than the round bent tubing that you commonly see.

The LFS store that built my stand made the light tree for me. The decided to go with square tubing due to the weight of the ATI PM. I'm happy with how it looks. Now if I can find the correct wire to mount the fixture. :rolleye1:

 

[FranktheTankTx]

How thick is the glass?

P.S. Would you mind pm-ing' me the total cost of this tank as well? As you can see in my signature, I'm planning something similar to yours. Just interested in a ball park figure.

 

[Giga]

how do u subscribe to this thread? Since the update I can't seem to find the button?


NM/ found it and way cool tank!

 

[lordofthereef]

Top of the line all the way heh?

 

[FranktheTankTx]

how do u subscribe to this thread? Since the update I can't seem to find the button?


NM/ found it and way cool tank!

Thread tools - subscribe. Located above OP.

EDIT: Ooops, too late!

 

[Boyman]

that is a sweet tank

I dig the equipment list

 

[mnml]

FranktheTankTx - the glass is 1/2" thick. PM sent.

lordofthereef - most of the stuff i got from holiday sales and f/s forum so i was able to save quite a bit on the equipment

 

[Snow Leopard]

Went all out! That's the way to go! I've never heard of LeeMar. Do they just do glass tanks or acrylic also?

 

[mnml]

Thanks Snow Leopard. LeeMar is a local builder here in SoCal, I believe they only do glass tanks. I haven't seen a LeeMar that was acrylic.

 

[SecGenGSX]

Sweet looking setup. Looking forward to seeing this progress.

 

[mnml]

Thanks SecGenGSX


I got the stand pipe installed this morning, I'm hoping it's not too short. Right now it's about 2" from the bottom of the overflow teeth to the top drain of the stand pipe. I'm going to do a water test later this week. Right now, I ran out of tubing for the sump plumbing so off to Home Depot I go...

 

[Jadams]

Looks great Tran!!! Excellent set up :thumbsup:

 

[Shorasp30]

Awesome! Looking forward to updates.

 

[mnml]

Thanks a bunch Jeremy and Shorasp30

I got the plumbing done tonight and also added two fans for better air circulation in the stand. One pulls air in while the other pushes air out. I was afraid of noise level but they're pretty quiet. Space is getting a little tight and still undecided where I'm going to place my ATO reservoir. We'll see...

Next I have to figure out the Apex controller and do some cable management. Hopefully I can do the water test this weekend and get the lights hung.

 

[mnml]

I had my sump builder make me this ATO reservoir. It holds about 7 gallons and should fit in the stand and still allow room for the dosing containers.