NUBIANTANGLOVER's New 265g Build Thread
- Thread starter NUBIANTANGLOVER
- Start date
I agree. More women are needed in this hobby. I have convinced my husband we need to upgrade and will take a whole year of planning before I fill the new one with water. I have been following your thread and your tank is awsome. I am having a 220g custom made for me in the near future and can't wait!
NUBIANTANGLOVER
New member
Great to hear from you & the other ladies as well! You should see how my girl family members look at me---like I'm insane. They think I'm suppose to spend all my money shopping for clothes. (LOL)
In any case, I'm sorry everyone for the delay. I installed my phosphate reactor and it's helping. I purchased the TLF (Two Little Fishes) brand. I followed everyone's advice via RC on purchasing this product & how to install it correctly and took a chance on the product. I am really pleased, thus far. Although, algae in a new 265g tank is something to deal with. It did look much worse.
Sadly, I noticed that my sump is leaking again from the point where it is plumbed via a bulkhead from the sump to pvc leading to my pump for the closed loop. I've tightened it and cracked the bulkhead straight down the middle of the threads.
This was my very first acrylic sump that was sealed by myself. Obviously, I goofed and I did not install it very well. I thought I fixed it completely by using aquarium silicone sealant like crazy. Well it held for months, and now I'm paying for it. The leak is not too bad, but I do have to place newspaper underneath the connection to catch the steady drip.
To fix this correctly, I'm going to have to disconnect only the pvc leading to the sump from the pump. Good thing I have shut-off valves. Next, I'm going to need to remove all the silicone gunk piled around the sump and bulkhead area. Clean the entire area and replace the new sump bulkhead correctly as well as the pvc pipe leading to the pump------(I have extra pvc for this already)--- all while underneath the stand, as the sump was too big that it had to be placed inside the stand from the back where there are no additional braces like those located on the front of the tank.
Also, I really can not move the tank since it is extra heavy, already in place and I do not want to risk the damage. Luckily, the stand's area is long and tall enough to completely access the sump area.
I really wish I could have someone to come over and help me. This is all new to me. Thus far, I've done everything else well. If anyone is proficient in this area and local here in Charlotte, I could use a helping hand.
Last edited:
gary faulkner
New member
Would love to help but I'm too far away.
There are lots of reefers in Charlotte, I'm sure someone will be willing to help. Have you thought about posting on the local forum? I believe it's called RASOC. Reef Aquarium Society of Charlotte.
There are lots of reefers in Charlotte, I'm sure someone will be willing to help. Have you thought about posting on the local forum? I believe it's called RASOC. Reef Aquarium Society of Charlotte.
huskerreef
New member
For what its worth, no silicone on the bulkhead. Reading your post I was not sure if you used silicone on the gasket from the beginning. I have tanks with a total of 6 bulkheads and not one has ever leaked, it should have a rubber gasket that goes on the inside of the tank and you should be able to tighten it enough to not leak. Also a little teflon tape on the threads of the pvc fitting, not on the bukhead threads. Hopefully this helps.
NUBIANTANGLOVER
New member
Gary,
I'm probably going to have to try it. I am hoping someone from RC will help asap, though. Thanks for the advice.
NUBIANTANGLOVER
New member
Jim,
I am sure you are correct, as I thought about the advice to add the silicone to the area given by the LFS after I had the system up and running. This is my second drilled system and I too never needed silicone for the bulkheads on the tanks. A little turning always does the trick. So, I'm sure I will be scraping away to remove the silicone from the sump. It does have a gasket, which is also on the insode of the tank. I just want this nightmare to end. I've worked hard to get this sytem up and running. My corals are doing well and so are the snails and my sweet coral banded shrimp.
gary faulkner
New member
After rereading your previous post, I think that the bulkhead may have been cracked already. I have had this happen before especially between the pump and bulkhead. Vibration or cheap bulkhead.
Why don't you try a new bulkhead, heavy duty. And maybe a piece of flex pipe from it to pump.
Hope all this makes sense.
Why don't you try a new bulkhead, heavy duty. And maybe a piece of flex pipe from it to pump.
Hope all this makes sense.
NUBIANTANGLOVER
New member
Thanks Gary! I do plan on purchasing a heavy duty bulkhead.
NUBIANTANGLOVER
New member
Okay everyone,
I am back with updates.
In regards to the cracked bulkhead...Gary was right. It was cracked prior to installation. I did go out and purchase a new bulkhead and additional plumbing supplies to correct the problem. However, What Do You Know: When I arrived home with the supplies, there was no leak. In fact, as of today, there has not been another leak. Of course, this can't be explained. I did decide to keep the supplies handy just in case it leaks again I will be ready and can replace it asap.
I am back with updates.
In regards to the cracked bulkhead...Gary was right. It was cracked prior to installation. I did go out and purchase a new bulkhead and additional plumbing supplies to correct the problem. However, What Do You Know: When I arrived home with the supplies, there was no leak. In fact, as of today, there has not been another leak. Of course, this can't be explained. I did decide to keep the supplies handy just in case it leaks again I will be ready and can replace it asap.
NUBIANTANGLOVER
New member
I will be posting several photos today on the update of my tank.
newreefbishop
Premium Member
Nice build thread, I will definately be following along.....
I love the desing so far and will definately be applying some of your practices to my next build. I am currently designing one for my father and havve to do it simple enough for an old Jamaican man to maintain it by himself
I love the desing so far and will definately be applying some of your practices to my next build. I am currently designing one for my father and havve to do it simple enough for an old Jamaican man to maintain it by himself
NUBIANTANGLOVER
New member
<a href=showthread.php?s=&postid=11927977#post11927977 target=_blank>Originally posted</a> by newreefbishop
Nice build thread, I will definately be following along.....
I love the desing so far and will definately be applying some of your practices to my next build. I am currently designing one for my father and havve to do it simple enough for an old Jamaican man to maintain it by himself
Thanks! I know it's been really slow, but so far I have been doing pretty okay as far as eliminating many mistakes. I will defintely post photos today. Just waiting on my lights to come on, which is on an automatic timer. Good luck with your new design for your father. RC has the best advice and wonderful people willing to help.
