Pacific Sun Kore 5th dosing Fan Club
- Thread starter Rudimenta
- Start date
I am happy to report that improved AWC functionality added in the upcoming firmware is working great. I currently have 16 min "waste out" cycle.
I am successfully changing out 20 gallons per day using my custom spectrapure pump system. I actually modified the set up a little and have my controller perform ATO when water level in the sump get too low during "waste out cycle". The refill is done using 3X concentrated saltwater and stops ones level reaches the optical sensor. By I adjust the optical level height based on how salinity changes and how long the refill cycle runs. This also allows me to slowly adjust salinity to the desired level.
The dosing is scheduled right before the AWC cycle starts.
I am successfully changing out 20 gallons per day using my custom spectrapure pump system. I actually modified the set up a little and have my controller perform ATO when water level in the sump get too low during "waste out cycle". The refill is done using 3X concentrated saltwater and stops ones level reaches the optical sensor. By I adjust the optical level height based on how salinity changes and how long the refill cycle runs. This also allows me to slowly adjust salinity to the desired level.
The dosing is scheduled right before the AWC cycle starts.
Nice. Any updates on the other functions along with a new version of the software? Thanks
Sent from my iPad using Tapatalk
I am still running the 1.6e software on my PC, which works perfectly fine with 1.7a firmware. Did not see any broken functionality in firmware but without new 1.7a software I do not know which features were added.
odd. my software i just downloaded and installed says 1.6c and firmware 1.6e? Also i do not see the new 1.7a firmware on the site? Maybe I have the wrong location? where are you downloading everything from?
Thank you
Any other fixes? How is it going with the new version?
Sent from my iPad using Tapatalk
I am not sure if I am supposed to share it. Hopefully Przemek chimes in here. I would email Thomasz and ask for it as Przemek suggested earlier.
Sent from my STV100-1 using Tapatalk
elFloyd
Member
Help Appreciated
Help Appreciated
I recently picked up this doser in 1st generation. Read through every post in this thread. Using iMAC and have the correct BT dongle. Playing with it all week to get familiar and all is going well. Decided to update firmware before going live. Received the Mac OS app for the firmware.
First time I tried it downloaded about 60k data. Then I got the message the update failed, click Rescue Mode > Update > Reset.
Then it downloaded about 100k data before it failed again. Received same message: click Rescue Mode > Update > Reset. After 110k download... same message.
Repeated the process, now the update seems stuck and I am afraid to touch anything.
Device resetted
firmware update in progress...
Used file - PSunFlash.app (1).zip
Please
wait........................................
..............................................
..............................................
..............................................
..............................................
Status on device says: Connected, Uploadiing...
Tri-position switch was moved from upper position > reset position > upper position.
Device is setting on my desk inches away from the BT dongle.
Any suggestions? I don't need an expensive brick.
Help Appreciated
I recently picked up this doser in 1st generation. Read through every post in this thread. Using iMAC and have the correct BT dongle. Playing with it all week to get familiar and all is going well. Decided to update firmware before going live. Received the Mac OS app for the firmware.
First time I tried it downloaded about 60k data. Then I got the message the update failed, click Rescue Mode > Update > Reset.
Then it downloaded about 100k data before it failed again. Received same message: click Rescue Mode > Update > Reset. After 110k download... same message.
Repeated the process, now the update seems stuck and I am afraid to touch anything.
Device resetted
firmware update in progress...
Used file - PSunFlash.app (1).zip
Please
wait........................................
..............................................
..............................................
..............................................
..............................................
Status on device says: Connected, Uploadiing...
Tri-position switch was moved from upper position > reset position > upper position.
Device is setting on my desk inches away from the BT dongle.
Any suggestions? I don't need an expensive brick.
Attachments
elFloyd
Member
After sitting in the above state for hours.... I took a power hit and lost all power to the house for about five minutes. Now the display is all boxes and I have this error message on the iMac: Error: Access violation at address 005AD635, accepting address 0265C3A6.
Attachments
intheshaddow
New member
It's rather unusual situation. Contact PacSun service via e-mail. I'm sure they will be able to help you as they helped me.
I use these lab grade glass ones. I think they are $2/piece. My wife is a researcher so I have access to these as well as tubings
Attachments
Same as to other promises, it never gets delivered on time [emoji44]. That's one thing I don't like about Pacific Sun - they never make good on their promises.
They have good products, but their promises about new apps or updates are never fulfilled on time, which is shame.
Sent from my iPhone using Tapatalk
Przemek_PacSun
New member
We are working on it - as we promised previously we will inform about that when it will be finally ready.. Not earlier - not later. Please be patient.
I see thats my fault that I told anything about software updates and forthcoming apps publicly. Writing apps and debugging them is something more complicated than simply building device/hardware. We will not release something which is not working or is early Beta version.
So I can say sorry - and I can promise that it will never happen again(information about any updates/soft versions).
It will not make any disappointments when anything will be released later than Customers expect.
Regards
Przemek
I see thats my fault that I told anything about software updates and forthcoming apps publicly. Writing apps and debugging them is something more complicated than simply building device/hardware. We will not release something which is not working or is early Beta version.
So I can say sorry - and I can promise that it will never happen again(information about any updates/soft versions).
It will not make any disappointments when anything will be released later than Customers expect.
Regards
Przemek
Yes Przemek, it's better to show the app when you already have it and not tell us that the app will be released let's say this weekend, and two months later your weekend still haven't arrived.
It's better to say that app or software will be released let's say after two months and then you actually release it earlier then promised. Now that would make everyone happy and not the other way around.
Still patiently waiting for the app and wishing you best of luck with your business [emoji106]
Sent from my iPhone using Tapatalk
