intheshaddow
New member
I use Android app on Moto G4 and it works spotless. No issues do far.
Wysłane z mojego Moto G (4) przy użyciu Tapatalka
Wysłane z mojego Moto G (4) przy użyciu Tapatalka
Pacific Sun Kore 5th dosing Fan Club
- Thread starter Rudimenta
- Start date
homer1475
New member
Android app on my S8+ works pretty good.
My only complaint is when the screen times out, it disconnects the app. I have to close the app before it will link with bluetooth again. Same can be said when you manually disconnect(pressing the connect button for a few seconds), the app will not reconnect until you close it and start again.
My only complaint is when the screen times out, it disconnects the app. I have to close the app before it will link with bluetooth again. Same can be said when you manually disconnect(pressing the connect button for a few seconds), the app will not reconnect until you close it and start again.
Figured it out.... nice job on the calibration. That is much easier than trying to stop pump at a specific amount.
Only issue I experience is if I disconnect, kore 5the screen goes wacko.
I just close the app and it seems fine. I will be watching parameters closely for the next couple days. I switched over to ATI essentials and need to figure out how much to set at...
Only issue I experience is if I disconnect, kore 5the screen goes wacko.
I just close the app and it seems fine. I will be watching parameters closely for the next couple days. I switched over to ATI essentials and need to figure out how much to set at...
Has anyone used android app along with an app on another operating system?
Back and forth?
First time I experimented with the android app somehow in the custom settings Friday was deselected on the Mac version of the pump used for ALK. I caught it since I check ALK each day.
I am not going to use the mac app if this version works. Is it possible to change pump speeds as in the mac/windows versions?
Thx
Back and forth?
First time I experimented with the android app somehow in the custom settings Friday was deselected on the Mac version of the pump used for ALK. I caught it since I check ALK each day.
I am not going to use the mac app if this version works. Is it possible to change pump speeds as in the mac/windows versions?
Thx
Przemek_PacSun
New member
Hi
In Android app there is no option for changing motor speed - however since we are including highest quality charmed BPT tubings - it's not needed.
Even on fast speed doser is ultra precise(offer much better resolution than any other dosing station on market).
But this Pharmed tubings REQUIRE fast speed - on moderate or precise rollers sometimes not spin and dosed amounts aren't consistent.
In next firmware release(which will be compatible with Kore 7th also) that option will be removed from software and firmware(it caused too many reports from Customers which tried to use Pharmed tubings but with precise speed - which is not needed for that kind of tubings).
Built in algorithms allow to dose single liquid drops even on fast speed using Pharmed tubing.
We got few reports about LCD screen strange letters after disconnecting - it should be fixed in nearest update(its not a bug in each doser - some dosers working inside cabinets where is strong EMC field "collect" some magnetic trash from air and thats responsible for this effect).
Regards
Przemek
In Android app there is no option for changing motor speed - however since we are including highest quality charmed BPT tubings - it's not needed.
Even on fast speed doser is ultra precise(offer much better resolution than any other dosing station on market).
But this Pharmed tubings REQUIRE fast speed - on moderate or precise rollers sometimes not spin and dosed amounts aren't consistent.
In next firmware release(which will be compatible with Kore 7th also) that option will be removed from software and firmware(it caused too many reports from Customers which tried to use Pharmed tubings but with precise speed - which is not needed for that kind of tubings).
Built in algorithms allow to dose single liquid drops even on fast speed using Pharmed tubing.
We got few reports about LCD screen strange letters after disconnecting - it should be fixed in nearest update(its not a bug in each doser - some dosers working inside cabinets where is strong EMC field "collect" some magnetic trash from air and thats responsible for this effect).
Regards
Przemek
Przemek_PacSun
New member
Sorry, I missed your question/
yes, manual is available there:
http://pacific-sun.eu/shop/dosing-stations/kore-5th-starter-edition/#tab-downloads
and direct link:
http://pacific-sun.eu/pliki/Kore5th_manual.pdf
Regards
Przemek
homer1475
New member
Przemek, I have always used the windows interface for calibration, and that's covered in the manual you linked to.
The android app appears different, and is not covered in the manual. How does one calibrate using the app. I would prefer to use the app as it's an easier to use(mobile always within arms reach, while laptop needs to be dragged out, started up, etc, etc).
The android app appears different, and is not covered in the manual. How does one calibrate using the app. I would prefer to use the app as it's an easier to use(mobile always within arms reach, while laptop needs to be dragged out, started up, etc, etc).
Homer it was pretty easy. (actually easier than what I was doing for calibration)
Choose desired pump-Select calibration, doser pumps fluid into your measuring container. Measure how much liquid was despensed,(visual markings on container) input this value, then save calibration.
You can then "check calibration" it should fill the container with the same amount again. (i did process twice)
Go into the actual pump settings and manually dose into the measurement container to see if dose was correct.
(i.e. set dose to 10ml doser should dispense 10 ml...)
Calibrate each pump.
It worked very good...
Choose desired pump-Select calibration, doser pumps fluid into your measuring container. Measure how much liquid was despensed,(visual markings on container) input this value, then save calibration.
You can then "check calibration" it should fill the container with the same amount again. (i did process twice)
Go into the actual pump settings and manually dose into the measurement container to see if dose was correct.
(i.e. set dose to 10ml doser should dispense 10 ml...)
Calibrate each pump.
It worked very good...
Last edited:
Przemek, FYI...My Kore 5th is in a cabinet...
(only piece of electrical equipment in cabinet)
-Ed
homer1475
New member
intheshaddow
New member
Przemek, can you tell us something more about this Kore 7th? Is it going to be your new 7 channel dosing station?
Wysłane z mojego Moto G (4) przy użyciu Tapatalka
Pete can you share how you got the upload of the Firmware successful for the Blank Screen issue?
I have a Blank Screen now and tried the Firmware process with no luck.
Thanks in advance...
Przemek_PacSun
New member
@wcharon
Procedure is the same - you need use dedicated software for update(not control software even if it have upload firmware button!) and press reset switch on doser after you will choose firmware to upload( "dots" are showing on app screen...)
Procedure is the same - you need use dedicated software for update(not control software even if it have upload firmware button!) and press reset switch on doser after you will choose firmware to upload( "dots" are showing on app screen...)
Przemek_PacSun
New member
Hi
We noticed some delays a specially with parts suppliers :-(
But now everything is fine - we are on last stage and our IT team do last software updates (to prepare Kore 7th to control class type calcium reactors ;-)
So general informations about Kore 7th:
- wireless dosing station with 7 separate dosing channels. Virtual bottles(low capacity alarms), precision up single drop!(important for Korallen Zucht/Aquaforest users where some liquids are calculated in drops/100 liters)
- digital temperature sensor
- 2pH electrode ports - which allow several configure options like:
a) 1 pH for controlling calcium reactor(it's dosing co2 using solenoid valve like in Kore 5th) - second for tank measure and alarm for too low pH in tank
b) 1 pH for controlling calcium - second to work with kH Lab for alkalinity measure and adjusting(by turning on/off solenoid in calcium reactor)
...
- automatic water change with dedicated DC AWC module(or 2 channels in doser)
- work with magnetic stirrer - mix liquids before the dose(like coral foods etc)
and many other options which will be explained/described in product manual..
We expect that product will be available for orders in next week - before endow January at least..
BR
Przemek
Last edited:
Syntax1325
Acro Addict
Latest firmware is very fast and stable! I'm using a tablet, I'm able to secure a solid connection with the doser from about 15 feet away through a wall and the tank cabinet... very happy with this update.
watsonj
10 & Over Club
doser will not shut off
doser will not shut off
I was calibrating pump#2 for the first time today as I was setting up for the first time and the screen went blank and the pump stayed running after 10min I unplugged the unit waited 5 min and plugged it back in.The screen flashed a bootloader message and then the time for a brief second and the screen then went blank and pump #2 runs continually I tried the reset button but it does the same thing and I can no longer connect to the doser via Bluetooth. What do I do?
doser will not shut off
I was calibrating pump#2 for the first time today as I was setting up for the first time and the screen went blank and the pump stayed running after 10min I unplugged the unit waited 5 min and plugged it back in.The screen flashed a bootloader message and then the time for a brief second and the screen then went blank and pump #2 runs continually I tried the reset button but it does the same thing and I can no longer connect to the doser via Bluetooth. What do I do?
