EllisJuan
New member
No problem. It really takes the Jebaos to the next level. I have mine setup with different feed, day, dusk/dawn, and night profiles so the intensity/frequency changes along with my lighting schedule.
anyone tried to using Jebo WP40?
- Thread starter chercm
- Start date
No problem. It really takes the Jebaos to the next level. I have mine setup with different feed, day, dusk/dawn, and night profiles so the intensity/frequency changes along with my lighting schedule.
fltekdiver
New member
jay13
New member
I just received my jaebo wp-40's with dual controller a week ago. My model has a built in night sensor so no more lost little pin sensors to buy. Also with the two pumps on one controller it really increases the capability of the pumps compared to others i have seen with two seperate pumps. Mine are on a glass 180 with a euro braced top and there is no way i could run them both wide open on most of the settings without water on the floor. I run the "c" setting with both pumps throttled down two settings. It is an amazing pump and really adds to the system.
Mind sharing your Apex settings
Please and thank you
fltekdiver
New member
I run 1- WP40 and 1- WP25 on my 180
The 40 I run with lowest setting
The 25 I run in else mode
Sent from my Samsung Galaxy S3 using Tap Talk
The 40 I run with lowest setting
The 25 I run in else mode
Sent from my Samsung Galaxy S3 using Tap Talk
jay13
New member
i have had zero problems with it so far. works every time the lights turn on or off without fail.
EllisJuan
New member
Mind sharing your Apex settings
Sorry, I just saw this.
Outlets:
WP25 -
Set Wave1
If Time 12:30 to 15:29 Then DuskDawn
If Time 15:30 to 01:29 Then Wave1
If Time 01:30 to 02:29 Then DuskDawn
If Time 02:30 to 12:29 Then Night
If Outlet Flush = ON Then Flush
If FeedA 000 Then Feed
WP10 (Mostly used for surface agitation)-
Set Wave10
If Time 12:30 to 15:29 Then DuskDawn10
If Time 15:30 to 01:29 Then Wave10
If Time 01:30 to 02:29 Then DuskDawn10
If Time 02:30 to 12:29 Then Night10
If FeedA 000 Then Feed10
Profiles:
Wave1:
Synchronize - Enabled
Divide by 10 - Enabled
Initial off time - 0
On time - 6
Off time - 4
Minimum Intensity - 0
Maximum Intensity - 55
DuskDawn:
Synchronize - Enabled
Divide by 10 - Enabled
Initial off time - 0
On time - 6
Off time - 4
Minimum Intensity - 0
Maximum Intensity - 45
Night:
Synchronize - Disabled
Divide by 10 - Disabled
Initial off time - 0
On time - 5
Off time - 15
Minimum Intensity - 30
Maximum Intensity - 50
Feed:
Synchronize - Disabled
Divide by 10 - Disabled
Initial off time - 0
On time - 10
Off time - 0
Minimum Intensity - 30
Maximum Intensity - 30
Wave10:
Synchronize - Disabled
Divide by 10 - Disabled
Initial off time - 0
On time - 10
Off time - 0
Minimum Intensity - 100
Maximum Intensity - 100
DuskDawn10:
Synchronize - Disabled
Divide by 10 - Disabled
Initial off time - 0
On time - 10
Off time - 0
Minimum Intensity - 70
Maximum Intensity - 70
Night10:
Synchronize - Disabled
Divide by 10 - Disabled
Initial off time - 0
On time - 10
Off time - 20
Minimum Intensity - 40
Maximum Intensity - 80
Feed10:
Synchronize - Disabled
Divide by 10 - Disabled
Initial off time - 0
On time - 10
Off time - 0
Minimum Intensity - 75
Maximum Intensity - 75
I also created a virtual outlet that runs a few times a day to blow my rocks clean...
Flush (Virtual outlet)
OSC 141:00/003:00/000:00 Then ON
If Time 01:30 to 15:29 Then OFF
If FeedA 000 Then OFF
Flush Profile for wp25:
Synchronize - Disabled
Divide by 10 - Disabled
Initial off time - 0
On time - 3
Off time - 2
Minimum Intensity - 0
Maximum Intensity - 90
Sacohen
New member
Cleaning I do every month or so. Some people feel the need for it more often.
Just turn the cage counterclockwise (If I remember correctly) and then pull everything apart and scrub it with a toothbrush.
If it gets caked with coraline then soak it in vinegar for 24 hrs then rinse well and put back in the tank.
Pretty much the same as cleaning anything else.
rrasco
Active member
I came to post this. They never seem to stop innovating eh? This looks promising....and AWESOME! I was going to get a few dual controllers but I may just make the jump to the RW. Somebody has to test them out.
Sacohen
New member
The more that I read and look into this, it is not wireless like the MP-40.
It looks like the connectivity of multiple pumps is wireless, but there is still power running into the pump.
I don't think it has a wireless controller either.
This is from their broken English manual...
"Wireless controllers allow synchronize operation among wave makers. One
main controller can remote control the sub-controllers"
It looks like the connectivity of multiple pumps is wireless, but there is still power running into the pump.
I don't think it has a wireless controller either.
This is from their broken English manual...
"Wireless controllers allow synchronize operation among wave makers. One
main controller can remote control the sub-controllers"
rrasco
Active member
That's basically all the Vortech's do. I wasn't expecting it to be cordless or go through the glass like an MP (I don't like that anyways).
When I bought a Vortech, I expected the wireless to be between the pump and the controller, but nope, big ol fat cable between them.
This is nice because you can have multiple pumps on a tank and have them aware of each other without using a dual controller and/or having cables connect them all together.
Similar threads
