ATI Powermodule Hybrid Club
- Thread starter rodneyri
- Start date
sahin
Ultimate Reefer
With a 4 tube LED PM, yes you can.
sahin
Ultimate Reefer
PM me with your email address with preferences, like how long a light cycle, how long to run T5's, T5 combo etc, whether you like 14K? 20K? etc, and I can create a light program for you. Let me know how many LED clusters you have as well.
w.vreeswijk
New member
Hey
I,m wesley from holland.
Yesterday i have buy a ati hybrid 8x54watt 3x75 led.
Tommorow i can pick him up.
Now i reading a lot.
How have you done the burnig in from the t5 bulbs.
And another question with programming on the pc how van i get the line on 3%.
Only i can set on 10%
Thank you
Greets wesley
I,m wesley from holland.
Yesterday i have buy a ati hybrid 8x54watt 3x75 led.
Tommorow i can pick him up.
Now i reading a lot.
How have you done the burnig in from the t5 bulbs.
And another question with programming on the pc how van i get the line on 3%.
Only i can set on 10%
Thank you
Greets wesley
sahin
Ultimate Reefer
Hello from UK!
Nice choice :lol:
Just run the T5's only without LED's on for 7 days at 7 hours over tank.
OR run the lights sitting on a table/safe area for 2 days (48 hours) continuous.
Either is fine.
ATI tubes are high quality and dont really need it. Main purpose for the burn is is to burn off contaminents and get everything stable within the tube.
In the software, click on SETTINGS. This will bring up box like this:
Now change the SPACING INTENSITY to 3 or 2 or 1 to change light intensity in those set increments. I highlighted in GREEN what you need to change.
Hope that helps.
sahin
Ultimate Reefer
If you cannot figure out how to use the controller, then please PM me with how you want the light profile. I will then create a light profile. You then just need a quick access to someones laptop etc to upload the light profile to your controller.
Yeah, it wasnt you who PM'd me....I get loads of PM's a week regarding this light fixture and creating custom light profiles...ATI should employ me as their technical service guy :lol: Seriously though, I dont mind helping out my fellow reefkeepers.
w.vreeswijk
New member
Hello from UK!
Nice choice :lol:
Just run the T5's only without LED's on for 7 days at 7 hours over tank.
OR run the lights sitting on a table/safe area for 2 days (48 hours) continuous.
Either is fine.
ATI tubes are high quality and dont really need it. Main purpose for the burn is is to burn off contaminents and get everything stable within the tube.
In the software, click on SETTINGS. This will bring up box like this:
Now change the SPACING INTENSITY to 3 or 2 or 1 to change light intensity in those set increments. I highlighted in GREEN what you need to change.
Hope that helps.
Ok thnx for the help.
I get it.
Is there not a file i can get.
So i can see a normal par table so i can make it my own.
I love the color of the set of reef in the sky
This ar the bulbs i buy
ATI Blue Plus
ATI Actinic
ATI Blue Plus
ATI Coral Plus
ATI Coral Plus
ATI Purple Plus
ATI Blue Plus
ATI Coral Plus
Now i,m running with a pacafic sun metis xm 3x150 on my tank.
I can,t wait to see the ATI on my tank.
Greets wesley
graham hunt
Premium Member
again thank you!
again thank you!
yes i bet you get loads of mail,thank you very much for the kind offer i have yet to review fitting,hang it and burn in t5s then i will try to set up the conntroller,do you by any chance know what the factory presets look like this may be a way i can start easily and change when i am a bit more confident.
thanks again i feel a lot less worried about the set up now.
regards graham.
again thank you!
yes i bet you get loads of mail,thank you very much for the kind offer i have yet to review fitting,hang it and burn in t5s then i will try to set up the conntroller,do you by any chance know what the factory presets look like this may be a way i can start easily and change when i am a bit more confident.
thanks again i feel a lot less worried about the set up now.
regards graham.
sahin
Ultimate Reefer
Cant recall the factory preset too much, but I remember it uses the Blue+, AQUABLUESPECIAL predefined presets for the LED's, and runs the T5's at full intensity.
Hi wesley you also here I still had contact with you about the artemio jbl right?
I'm going to 65cmx65cm my cube 60cm high with dual black back wall for equipment and Deltec MCE 600 am here to find out what lighting I take probably the ati hybrid 4 x 24 The 8x24 is probably just too wide (strooilicht) hope that is enough for sps?
What do you think Greeting Wijnand from Dordrecht
graham hunt
Premium Member
first try
first try
hi thought i would share,
put t5s in easier than i thought,did not need to grip lamps they roll at each end into place.
ran demo.
hung lamp i was on my own,put braces across the tank to support fitting,centre it up,fitted wires,hoisted up leveled at 12"above water level,easy enough but it is a heavy fitting another pair of hands for peace of mind recommended!
cable length was a nice supprise easily reached the floor(my safe zone)easy connect up,switched power on and set time.
think i have selected a factory reset/set one,rolling indicator was a supprise telling you the status of each channel
it was late 4pm so only leds came on i had run out of energy so i will let it run through its paces till tomorow see what happens!
very impressed with colour and front to back cover i was expecting ends a bit shaded,think this will improve with t5 when on.this tank sits next to a large cube with 400w radium 20k leds look the same colour but much more detail
i checked par on surface at 3.00 o/c pm(350)which is lower than led fittings it replaced so think my sps will have a gentle transition.
very happy thus far see what it looks like and possibly have a play tomorrow
sorry no pics until i can tempt a pal over to take some and upload them for me.
regards graham
first try
hi thought i would share,
put t5s in easier than i thought,did not need to grip lamps they roll at each end into place.
ran demo.
hung lamp i was on my own,put braces across the tank to support fitting,centre it up,fitted wires,hoisted up leveled at 12"above water level,easy enough but it is a heavy fitting another pair of hands for peace of mind recommended!
cable length was a nice supprise easily reached the floor(my safe zone)easy connect up,switched power on and set time.
think i have selected a factory reset/set one,rolling indicator was a supprise telling you the status of each channel
it was late 4pm so only leds came on i had run out of energy so i will let it run through its paces till tomorow see what happens!
very impressed with colour and front to back cover i was expecting ends a bit shaded,think this will improve with t5 when on.this tank sits next to a large cube with 400w radium 20k leds look the same colour but much more detail
i checked par on surface at 3.00 o/c pm(350)which is lower than led fittings it replaced so think my sps will have a gentle transition.
very happy thus far see what it looks like and possibly have a play tomorrow
sorry no pics until i can tempt a pal over to take some and upload them for me.
regards graham
sahin
Ultimate Reefer
For an Chalice and Acan tank, go with your T5 combo as follows:
Front:
ATI Blue+
ATI Actinic
ATI Purple+
ATI Blue+
--LEDs--
ATI Blue+
ATI Actinic
ATI Purple+
ATI Blue+
Back
I will email you a program either this evening or tomorrow. I will include a decent amount of white light from the LED's so it wont look too blue.
sahin
Ultimate Reefer
Drop me a PM with the following info and your email address:
1. SPS or LPS dominated tank?
2. How long you want T5's to run? - At 100% or less? (Start and end time)
3. How long you want LED's to run? - At 100% or less? (Start and end time)
I can then make up a light profile for you and you can play with it and adapt to your liking.
Here is a Video Tutorial I created a while ago. You should be able to follow this to create your own profile as well:
<iframe width="640" height="360" src="//www.youtube.com/embed/Lh6f4JA9UUI" frameborder="0" allowfullscreen></iframe>
graham hunt
Premium Member
little update
little update
perhaps might help other people who like me are not able to use computor software and are a little worried about their ability to use this light.
t5s were not working after installation, took fitting down and checked them two were not secured properly, fitting back up now all working perfectly!
the fitting(5 foot four tube)is over a 8 footxtwo footxtwo foot sps tank,at one foot over water surface,it covers back to front perfectly and gives a good cover over length with a slightly shaded ends still plenty to bring out star polyps and with a little change to rockwork i feel is fine for me.
i measured 650 par at midday with t5 and factory setting,over nearly all of tank surface,the standard colour looks nice to me and it seems to start at 10o/c am ramping up seamlessly and ramps down again seemlessly to a 10o/c moonlight.my t5s front to back are:
b+
ab
led
p+
b+
i am very happy with light ,it was and is very simple to set up with controller only and for me gets you easily started out of box without any drama.
so happy i fact if i can sell another body part i will get a three foot unit for other tank holding clams ,gorgonions,gonapora and lps replacing 400w halide without any reservations about my ability to set it up.
regards graham.
little update
perhaps might help other people who like me are not able to use computor software and are a little worried about their ability to use this light.
t5s were not working after installation, took fitting down and checked them two were not secured properly, fitting back up now all working perfectly!
the fitting(5 foot four tube)is over a 8 footxtwo footxtwo foot sps tank,at one foot over water surface,it covers back to front perfectly and gives a good cover over length with a slightly shaded ends still plenty to bring out star polyps and with a little change to rockwork i feel is fine for me.
i measured 650 par at midday with t5 and factory setting,over nearly all of tank surface,the standard colour looks nice to me and it seems to start at 10o/c am ramping up seamlessly and ramps down again seemlessly to a 10o/c moonlight.my t5s front to back are:
b+
ab
led
p+
b+
i am very happy with light ,it was and is very simple to set up with controller only and for me gets you easily started out of box without any drama.
so happy i fact if i can sell another body part i will get a three foot unit for other tank holding clams ,gorgonions,gonapora and lps replacing 400w halide without any reservations about my ability to set it up.
regards graham.
sahin
Ultimate Reefer
Similar threads
