EuroReef Club

Status
Not open for further replies.
yes weld on 16 is for a more coarser job if you are glueing 2 pieces together and there is a crappy edge you use #16 on it for a finer joint you use #3 hth


mike
 
i know this has been going on for a couple weeks but i finally found the culprit in my water and it was copper, somehow it got into the water when i originally filled my system with tap water, now i have an ro/di system, but would rather not replace all the water..

it was a poly pad that turned blue that let me know what was going on, and i put in a metal sponge, and some sorta copepr remover that already came in its own bag, dont really know anything about it the lfs ordered it for me, but how long after i remove the metal remover should i try my euroreef again...and should i add another poly pad once its done to ensure that all of it has been removed?

thanks for your help again

-jeff
 
Hello ER club,
I have been holding off buying one with all the changes going on, but I thought you could help me with a couple of questions? Will the new Eheim pumps replace the current Gen-X's on all the skimmers? RC and non RC?
Also, on the Gen-X 6000 (RC250) pump it states 130watts and on the ER site it's listed at 60watts. Why is there such a difference here? Twice as much watts seems like a lot, no?

Thanks guys, I'll be joining you soon. Oh, I e-mailed ER but have not gotten a reply.

Thanks!!!!!!!!!
 
I am thinking about buying a RC500, a LFS offered me a used RC1000 - has anybody seen a RC1000 in action - I think it has 4 pumps and is 48" tall.
 
<a href=showthread.php?s=&postid=8123859#post8123859 target=_blank>Originally posted</a> by crabsy
Hello ER club,
I have been holding off buying one with all the changes going on, but I thought you could help me with a couple of questions? Will the new Eheim pumps replace the current Gen-X's on all the skimmers? RC and non RC?
Also, on the Gen-X 6000 (RC250) pump it states 130watts and on the ER site it's listed at 60watts. Why is there such a difference here? Twice as much watts seems like a lot, no?

Thanks guys, I'll be joining you soon. Oh, I e-mailed ER but have not gotten a reply.

Thanks!!!!!!!!!
Click to expand...
if you just plug it in with no water it pulls 45 watts if you put the stock water impeller in it , and put it in the water it pulls 130 watts diffrent types of nw-impellers in the water and venturis makes it fall in between the two.

ill be comparing perfromance of the ER nw with my GG wheel, paddle and the mesh wheel this weak. It will be interesting to see witch pull most air, least water, and least watts.
 
<a href=showthread.php?s=&postid=8125535#post8125535 target=_blank>Originally posted</a> by angelopasto
I am thinking about buying a RC500, a LFS offered me a used RC1000 - has anybody seen a RC1000 in action - I think it has 4 pumps and is 48" tall.
Click to expand...


Well think about it its a RC 1000 it cant be bad..
 
FWIW.
I just got thur testing the ER pump, im compring some things, i thought some of you may find some interest in my results. i was suprised to see it drove my 6'8" skimmer.


The first test was the "new" Euro Reef Gen-X 6000 as is. sorry but ive only tested it so far. Heres what i got.

Water head 6", - SCFH 35, - Watts 44 .
Water head 12", - SCFH 32, - Watts 49 .
Water head 18", - SCFH 26, - Watts 54 .
Water head 24", - SCFH 25, - Watts 58 .
Water head 30", - SCFH 23, - Watts 62 .
Water head 36", - SCFH 19, - Watts 65 .
Water head 42", - SCFH 18, - Watts 68 .
Water head 48", - SCFH 17, - Watts 70 .
Water head 54", - SCFH 16, - Watts 72 .

The height was messured from the pump outlet being 0".
The skimmer 8" dia
The pump was direct into the skimmer via Uni Seal.
the pump was set up as a recirc config.
 
Hello, I was wondering if someone could help me…

I have a CS8-1 with the Sedra 5000 pump and all I seem to get is large bubbles. After washing the skimmer cup clean I get a nice frothy foam which lasts about one day and then it goes flat. Where all I get after this is large bubbles, kind of like soda carbonated bubbles.

I was wondering if something is wrong with my skimmer or if there is something I could do to always have a nice frothy foam? Do you think it's because my water is too clean (I use purigen and phosguard 24/7)?

Thanks for your help. :)
 
check the venturi line and volute... also have a gander at the needlewheel itself and make sure no debris is in it.
 
<a href=showthread.php?s=&postid=8143395#post8143395 target=_blank>Originally posted</a> by Kip
check the venturi line and volute... also have a gander at the needlewheel itself and make sure no debris is in it.
Click to expand...
All checked out, the skimmer is brand new even though discontinued. It has been acting like this since day one.
 
the bubbles at the top that spill skimamte into the cup are large... or the bubbles in the skimmer body.

in the skimmer body... the bubbles should be tiny making the body pretty much white when you look at it.
 
First of all thanks for your help. :) The bubbles in the skimmer body are small and it does look completely white. The problem is with the bubbles in the neck, they are large watery bubbles. The only time the bubbles are frothy is 24 hours after the cup and neck are washed.
 
how high is your riser tube? (determine water/bubble line in the neck)... i run mine pretty high (with a gate valve)... so about an inch or so above the water line the bubbles spill over into the collection cup. if yours isnt set high, dont do it really fast... you will be constantly flooding the cup, but week by week you can work the riser up (and if that doesnt get you where you wanna be, then try the gatevalve mod for more fine tuning as well as not having to clean that foam filter anymore)

sounds to me it is acting normal... just set really low.
 
<a href=showthread.php?s=&postid=8143589#post8143589 target=_blank>Originally posted</a> by Kip
...about an inch or so above the water line the bubbles spill over into the collection cup.
Click to expand...
That's where I'm running mine, but no joy. :(
 
Anyone know the transition plan to change over to the ehiem pumps? I have read they are silent...?

How about the current pumps GenX 4100 are they silent ??

I'm looking at getting the CS400. Of all the popular choices based on service quality and rep. Seems to be the best deal going...?
 
i use eheim 1260 on my skimmer , the pump quite compare to the genx6000. there is not big different with the skim result (but compare to the genx6000 the eheim push less water to the skimmer body i believe if it was the eheim 1264 the improvment was different) . i need to make more test between those pump. when i try on the genx with the DLS material the pump get more quite and it's pull more air then the regular impeller the skim result was higher. i am going to make more test on those pump and wait to get other impeller to the genx .
 
Last edited:
wolf - not exactly sure when it will be but should be soon as they a should have the test ones in thier possesion now

Lunchbucket
 
Status
Not open for further replies.

Similar threads

Radicaljbr
Monitoring and dosing
Replies
2
Views
246
ReefKG
ReefKG
machodik
My Tunze 6095
Replies
9
Views
433
machodik
machodik
U
Goniopora
Replies
3
Views
178
Uncle99
Uncle99
jasonfrey
Red Sea ReefWave Pump Giveaway
Replies
0
Views
39
jasonfrey
jasonfrey
jasonfrey
Bubble Magus Medium Filter Roller GIVEAWAY
Replies
0
Views
40
jasonfrey
jasonfrey
Back
Top