Noisy Vortech DrySide FIX!!
- Thread starter dahenley
- Start date
redfishblewfish
Member
You have an MP40. I'm convinced this is a lateral force thing that is causing the noise. Try setting your glass thickness setting to the next thinner glass, and see if that helps.
Just an update, I took apart for the fifth time and repressed my bearings to make are they were on all the way.
I also figured out the sequence for washers. The tank side should get a single washer. The rear side should go washer, spring, washer. Hooked back up and is quieter. Not silent like my tunze, but much better. My wife said, that's supposed to be quiet? So I will continue to have my controller turn it off during dinner hours. But it is half the noise level as prior to bearing fix.
I also figured out the sequence for washers. The tank side should get a single washer. The rear side should go washer, spring, washer. Hooked back up and is quieter. Not silent like my tunze, but much better. My wife said, that's supposed to be quiet? So I will continue to have my controller turn it off during dinner hours. But it is half the noise level as prior to bearing fix.
coralreefdoc
New member
Love/hate relationship, to the maximum !
Fortunately/personally, my love for all the organisms I maintain/propagate alleviates any hard feelings between myself and guests' sense of hearing ...
* There's a reason that letter would've fallen on "deaf ears", Andrew ! :lol:
Fortunately/personally, my love for all the organisms I maintain/propagate alleviates any hard feelings between myself and guests' sense of hearing ...
* There's a reason that letter would've fallen on "deaf ears", Andrew ! :lol:
coralreefdoc
New member
In all seriousness, EcoTech Marine, specifically their innovative Vortech pump, has revolutionized this hobby in terms of the crucial water flow aspect ... Allowing many skilled ReefKeepers the ability to keep species never thought possible before, and should be praised for such endeavors !
If anything, the wetside on the MP40s should/needs to be redesigned-reengineered, in order to fully incorporate the shaft onto the end of the outer housing/shell, much like that of the MP10/MP60s !
It is because of this instability, in my experienced/professional opinion, that other secondary noise/inefficiency issues arise, both in the wetside as well as the dryside, ultimately ! I've personally been redesigning a model/replica, incorporating this aspect into the wetside, which Ill be presenting to Tim in the near future ... Keep your fingers crossed that he adopts this new wetside, for inevitable mass production, as it will undoubtedly decrease many of the aforementioned issues :thumbsup:
If anything, the wetside on the MP40s should/needs to be redesigned-reengineered, in order to fully incorporate the shaft onto the end of the outer housing/shell, much like that of the MP10/MP60s !
It is because of this instability, in my experienced/professional opinion, that other secondary noise/inefficiency issues arise, both in the wetside as well as the dryside, ultimately ! I've personally been redesigning a model/replica, incorporating this aspect into the wetside, which Ill be presenting to Tim in the near future ... Keep your fingers crossed that he adopts this new wetside, for inevitable mass production, as it will undoubtedly decrease many of the aforementioned issues :thumbsup:
Buganddoug
X NJRC Vice President
Not to rub it in but I am glade mine is very quite.
coraladdict
New member
I have the mp40,which ones did you use from Boca,can you post the link to the bearings?
Thank you
Buganddoug
X NJRC Vice President
http://www.bocabearings.com/productDetail.aspx?ItemID=3200
MR607-2RU TH9/C3 Radial Bearings
7 x 19 x 6 Millimeters
Bearing Material Chrome Steel 52100
Ball Material Chrome Steel 52100
Dimension Type
Metric
ID (d) 7
OD (D) 19
Width (B1) 6
Flange OD (D1) 22
Flange Width (Bf1) 1.5
Enclosure # Two Seals
Enclosure Material Rubber Seal
Enclosure Type Contact Seal
Retainer Material Polymite Plastic
ABEC/ISO Rating ABEC#1/ISOP0
Radial Play C3
Lube Kyodo PS2 Grease
RPM Grease (x1000) 33.3
RPM Oil (x1000) 44.6
Dynamic Load (Kgf) 238
Basic Load (Kgf) 91
Working Temp Deg C 121
Weight(g) 7.15
http://www.bocabearings.com/bearing-inventory/Radial-Bearings/1397/8x19x6-XMR698EPS
X-MR698-EPS Radial Bearings
8 x 19 x 6 Millimeters
Bearing Material Chrome Steel 52100
Ball Material Chrome Steel 52100
Dimension Type Metric
ID (d) 8
OD (D) 19
Width (B1) 6
Enclosure # Two Seals
Enclosure Material Red PTFE Seal
Enclosure Type Removable (S)
Retainer Material Chrome Steel
ABEC/ISO Rating ABEC#1/ISOP0
Radial Play P25
RPM Grease (x1000) 32.4
RPM Oil (x1000) 38.7
Dynamic Load (Kgf) 228
Basic Load (Kgf) 94
Working Temp Deg C 121
Weight(g) 681
MR607-2RU TH9/C3 Radial Bearings
7 x 19 x 6 Millimeters
Bearing Material Chrome Steel 52100
Ball Material Chrome Steel 52100
Dimension Type
Metric
ID (d) 7
OD (D) 19
Width (B1) 6
Flange OD (D1) 22
Flange Width (Bf1) 1.5
Enclosure # Two Seals
Enclosure Material Rubber Seal
Enclosure Type Contact Seal
Retainer Material Polymite Plastic
ABEC/ISO Rating ABEC#1/ISOP0
Radial Play C3
Lube Kyodo PS2 Grease
RPM Grease (x1000) 33.3
RPM Oil (x1000) 44.6
Dynamic Load (Kgf) 238
Basic Load (Kgf) 91
Working Temp Deg C 121
Weight(g) 7.15
http://www.bocabearings.com/bearing-inventory/Radial-Bearings/1397/8x19x6-XMR698EPS
X-MR698-EPS Radial Bearings
8 x 19 x 6 Millimeters
Bearing Material Chrome Steel 52100
Ball Material Chrome Steel 52100
Dimension Type Metric
ID (d) 8
OD (D) 19
Width (B1) 6
Enclosure # Two Seals
Enclosure Material Red PTFE Seal
Enclosure Type Removable (S)
Retainer Material Chrome Steel
ABEC/ISO Rating ABEC#1/ISOP0
Radial Play P25
RPM Grease (x1000) 32.4
RPM Oil (x1000) 38.7
Dynamic Load (Kgf) 228
Basic Load (Kgf) 94
Working Temp Deg C 121
Weight(g) 681
Last edited:
redfishblewfish
Member
I would surmise that there would be less wear because there is less lateral force on the bearings. You just want to make sure you use the mounting tab with the zip ties to make sure the dry side doesn't fall off the side of the tank.
babyjess210
Active member
I wanted to give my experience with this rebuild. I purchase a used MP40W Gen 2 and notice that the dry side is a little louder than my 6 month old MP40W Ecosmart. I find this fabulous thread and took my dry side apart and the front bearing had a little red film on the bearing and shaft. I order a couple bearings from Amazon and now it is quieter than the Ecosmart.
BTW are you guys using any thread lock on the screw in the center of the magnet??
Here are the bearings from amazon:
S607ZZ Bearing 7x19x6 Stainless Steel Shielded Miniature Ball Bearings VXB Brand
S698ZZ Bearing 8x19x6 Stainless Steel Shielded Miniature Ball Bearings VXB Brand
BTW are you guys using any thread lock on the screw in the center of the magnet??
Here are the bearings from amazon:
S607ZZ Bearing 7x19x6 Stainless Steel Shielded Miniature Ball Bearings VXB Brand
S698ZZ Bearing 8x19x6 Stainless Steel Shielded Miniature Ball Bearings VXB Brand
coraladdict
New member
Buganddoug
X NJRC Vice President
No problem at all.
dahenley
New member
sczlars
Member
great thread; I'm ordering a pair of BOCAs 
. I recently got a used MP40WES, and while not too noisy, it isn't as quiet as my MP10, and I'm hearing some rattling that makes me thing the bearings are worn.
I noticed today when I had the spacer off, that the magnet-disk on the dry side doesn't turn true; seems like it is wobbling slightly. Anybody else seen this? The unit, when running in my hand, has a slight vibration to it. Maybe I bought a dud.
--Lars
. I recently got a used MP40WES, and while not too noisy, it isn't as quiet as my MP10, and I'm hearing some rattling that makes me thing the bearings are worn.I noticed today when I had the spacer off, that the magnet-disk on the dry side doesn't turn true; seems like it is wobbling slightly. Anybody else seen this? The unit, when running in my hand, has a slight vibration to it. Maybe I bought a dud.
--Lars
I think in the next month or so I'm going to try this again. I tried this before a couple years ago and I'm not sure if I followed up in this thread or not.
A couple years ago I ordered two of these exact bearings from boca: SMR147C-2OS #7 NB2 to replace the very noisy ones in my MP10. No issues getting them off or on. For about the first week it was dead silent, then the noise started slowly returning which I compensated for by turning the pump speed down. Until over the course of about 2-3 months it was once again too noisy even with the MP10 turned practically all the way down to live with anymore.
For about the past year the vortech has been living in the drawer. Dug it out today and cleaned it up and think this time I'll try just whatever cheap, steel ball, rubber sealed bearing I can find on Boca and see if they last any longer than the previous ones.
A couple years ago I ordered two of these exact bearings from boca: SMR147C-2OS #7 NB2 to replace the very noisy ones in my MP10. No issues getting them off or on. For about the first week it was dead silent, then the noise started slowly returning which I compensated for by turning the pump speed down. Until over the course of about 2-3 months it was once again too noisy even with the MP10 turned practically all the way down to live with anymore.
For about the past year the vortech has been living in the drawer. Dug it out today and cleaned it up and think this time I'll try just whatever cheap, steel ball, rubber sealed bearing I can find on Boca and see if they last any longer than the previous ones.
Buganddoug
X NJRC Vice President
One more thing. The higher the rating on the bearing the harder the material the louder the bearing will be.
coraladdict
New member
I have been using these bearings now for about 6 weeks .At the begining they were silent now they are noisy.
Are there any other bearings that will last longer than those posted in my thread?
dannyp1512
New member
hi
will this do the job on my mp10
http://simplybearings.co.uk/shop/p5...roove+Ball+Bearing+7x14x5mm/product_info.html
will this do the job on my mp10
http://simplybearings.co.uk/shop/p5...roove+Ball+Bearing+7x14x5mm/product_info.html
