NUBIANTANGLOVER's New 265g Build Thread

NTL, one other question, do you think a 75g tank (48x18x20) would fit under that stand? Could I get it in from the back?
 
nubian, you got that right, got a question for you, is that southdown sand you have recently purchased? and is it the reefsafe type?
 
yeah they have a whole pallet sittng at home depot. I will definately pick some up and put it in my fuge. I am setting up a 29g as well and will probably be trying it out there as well. thankls for the info.
 
<a href=showthread.php?s=&postid=10714663#post10714663 target=_blank>Originally posted</a> by discocarp
Ya, I don't understand this either!

Also, FYI, I called perfecto and they said you should put 1/2" styrofoam between the stand and tank. I'm getting the tank delivered so I hope they bear with me while I size and cut the foam!

Sure, I will explain,

If you look at the tank's stand it has a nice edging (molding) around the top of it. This is actually around 3 sides: the front and the left and right sides. However, the back does not have this molding. The molding actualy creates a simple tongue and groove
for the tank. Simply, the tank is placed on top of the stand, but the edges of the tank slides into the tongue/groove created by the molding on all 3 sides. It is slid from the back up towards the front.

Here's a photo of the tank & stand:

33201265g_Side_Photo_with_Water.JPG


As you can see from this side photo, there is molding around the sides and not the back. The way the molding is constructed, it also creates a simple tongue and groove in the inside where the tank meets the stand, enough to secure/support the bottom brace of the tank.

I didn't use styrofoam between the stand and the tank. I am sure it can only help.
 
<a href=showthread.php?s=&postid=10714904#post10714904 target=_blank>Originally posted</a> by discocarp
NTL, one other question, do you think a 75g tank (48x18x20) would fit under that stand? Could I get it in from the back?

You should not have a problem, as the stand is 87" long. But, you will have to remove the middle brace in the back of the stand. It is stapled and glued securely. I had my husband to use a saw to saw remove it. This is the only way you can fit the 75g tank underneath the stand. My sump, I believe, is 36" and I had to do this. The doors only allow a clearance of about 30".
Make sure you do this prior to placing the stand on the tank, so you will not disturb the tank when using the saw----as the wood is thick. And, to avoid sliding the tank back and forwards to get access to the back, where you would need to install the tank.
 
<a href=showthread.php?s=&postid=10720231#post10720231 target=_blank>Originally posted</a> by aceheart1976
nubian, you got that right, got a question for you, is that southdown sand you have recently purchased? and is it the reefsafe type?

This Southdown sand is 100% reefsafe. I used it in my 175g Bowfront for about 3 years with no problems. Now, this batch I'm using is from a huge order I made about 3-4 years ago. I had enough left over, apparently to use for this new tank. I kept the sand stored in my garage the entire time. It is still fresh.
 
I got mine last night. I see exactly what you mean about the molding! Getting the sump in is going to seriously vex me. I refuse to modify the stand, so this is gonna be fun lol!

This thing is a beast! You are right about the pictures not doing the size justice.

You are using the stock overflow kit, right? Is it loud when its running? How much is your return flow from the sump?
 
<a href=showthread.php?s=&postid=10721918#post10721918 target=_blank>Originally posted</a> by FUA
So southdown sand is silica free. Is there a way to test just to be sure.

Yes, many RC members on this forum have conducted silica tests for all different types of sand. There is a huge thread here on RC about Southdown. You can simply do the search "Southdown" to find them. Usually, from my understanding, the various sand types are tested using via a Fizz Test. Vinegar is the main ingredient for this.

I did some research for you and found the ultimate Southdown RC thread, created by "Grumpy Vet," known as an expert on Southdown. You will enjoy it:

http://reefcentral.com/forums/showthread.php?s=&threadid=26193&highlight=southdown
 
<a href=showthread.php?s=&postid=10722100#post10722100 target=_blank>Originally posted</a> by NUBIANTANGLOVER
Yes, many RC members on this forum have conducted silica tests for all different types of sand. There is a huge thread here on RC about Southdown. You can simply do the search "Southdown" to find them. Usually, from my understanding, the various sand types are tested using via a Fizz Test. Vinegar is the main ingredient for this.

I did some research for you and found the ultimate Southdown RC thread, created by "Grumpy Vet," known as an expert on Southdown. You will enjoy it:

http://reefcentral.com/forums/showthread.php?s=&threadid=26193&highlight=southdown

Sorry, for the Delay, I am really tring to be patient and take it slow so I will not mess anything up. So far, it's paying off. Well, to answer your question, The overflows are pretty quiet. The overall system is somewhat okay, I can basically hear my pump's motor, but it is not too loud either. I purchased the Sequence Reeflo Dart pump b/c of its rave reviews here on RC.
 
Okay Everyone,

I am back with additional updates, as well as photos! The biggest obstacle I faced thus far, was getting my sump intact and to eliminate the steady leak I had with the bulkhead attached to my sump. Finally, that battle has been won. Thanks to many prayers as well as silicone and plumber's glue, the problem has been resolved!!!
 
The skimmer was cleaned thoroughly using pure-distilled vinegar soaked in a very tall bucket. I then easily wiped all the old residue from the skimmer. For those of you who are just chimming in, I am using the ASM G2 Skimmer used on my 175 Bowfront. Immediately after hooking this bad baby up, it went to work!
I did a little research, and the ASM skimmers are no longer being made. They are being replaced by a new line by the manufacturer. The "Octopus Skimmer" line. The new website is www.octopusskimmer.com/
It's sad to see these skimmers being replaced as they totally rocked. They were basically a replica of the EuroReef, which is a fantastic skimmer, but at a very hefty price. I say all this as I know I am gonna have to upgrade my skimmer to handle my new system. For now, it is working swell so I am going to use all the extra time I have saving/researching for an upgrade.

Here's a photo of my ASM G2 Skimmer:
33201ASM_G2_Skimmer.JPG
 
For starters, I purchased 44lbs of pre-cured Liverock from Marine Depot. They price was really nice and the actual liverock I received were awesome! I know 44lbs is merely nothing for a 265g, but it will defintely work for my overall plan.
The rock was placed into the tank, in no particular design. My main objective was to get it in the tank to begin cycling. Some of the pieces were secured via black zipties. I used "black" as it will hide easily as opposed to lighter colored zipties.

Here is a photo of my tank w/ 44lbs of liverock. The rocks look so small.

;)

33201265_Only_LiveRock_A.JPG
 
Last edited:
To further help with my liverock/bioload as well as aquascaping, I ordered about 100lbs. of the famous, Marco Rock. Marc Rock is basically man made rock. Simply seed the rock with liverock and it will turn overtime into pure beautiful liverock! They give very, very nice pieces either in Fiji (my favorite) or Tonga style. I am very pleased with the size, texture, and shapes of the rock. Simply beautiful and at very affordable prices. You simply can not beat this product. It is an excellent way to obtain the rock you need at a great price, save on the environment and produce a fabulous saltwater/reef system. The website is: www.marcorocks.com

Here are several photos of the MarcoRock purchased!

33201Marco_Rock_A.JPG

33201Marco_Rock_F.JPG

33201Marco_Rock_B.JPG
 
I have added almost all of the Marco Rock to my system. I am trying to figure out where will I put all of this beautiful rock.
Here is a picture of my system w/ the MarcoRock added:

33201265g_Marco_Rock_B.JPG


And, as I couldn't resist the photo of his son by the aquarium in niloc's 265g thread, here is a photo of my son by my 265g new system. The photo really helps the observer gain a better appreciation of the tank's size. Hope you like it:

33201265g_with_Jordan_B.JPG
 
Last edited:
I am currently monitoring my system's parameters to see how far along the cycle is going. I have only had it cycling for a little over two weeks. However, my tank seems to have cycled. The tank was filled alomst instantly with diatoms and the ugly brown algae. I just let it take it's course. The algae bloom has decreased tremendously. I am still testing for ph, temp, nitrite, nitrate & ammonia. Slowly, but surely...I think I am ready.

However, like others have experienced my temperature is off the charts! I mean, the temperature is some 89.5 degrees ! So, of course I need to find a solution to this ASAP before I can even think about ading any live organsims to this system. I am looking into a series of fans or as a last result, a chiller. Any assistance will be greatly appreciated!
 
I have also noticed how quickly my sump water level decreases. So, I am also researching ways I can auto-fill or easily maintain the water levels in my sump. I have heard a little about peristalic pumps etc. Having a 7ft long stand and tank, I definetly have room to place other pieces of equipment underneath my stand. Anyone with advice, please comment. Thanks!
 
Looks like you are making great progress.

Don't forget to edit your profile to reflect the new 265.

Hope you find an answer to the heat problem without running a chiller.

Wish I had the answer, Here's hoping someone does!
 
<a href=showthread.php?s=&postid=11019519#post11019519 target=_blank>Originally posted</a> by gary faulkner
Looks like you are making great progress.

Don't forget to edit your profile to reflect the new 265.

Hope you find an answer to the heat problem without running a chiller.

Wish I had the answer, Here's hoping someone does!

Thanks Gary! You're right: I really need to update my RC membership tp reflect the 265g. Thanks.
I am currently reading here on RC about the use of cooling fans instead of chiilers. RC members have had some great success with these. So, I am still researching for the best brand, amount etc. I still need to research about top-off systems to control my evaporation levels as well as kalkreactors etc. to help maintain my calcium levels.
 
looking great so far nubian, i just picked up my 180 gal tank so its sitting in my storage until i can get the house built that it is going in
 
Back
Top