Official: Masterflex Calcium Reactor Setup Thread

I don't see why you can't but I also thinks the screw in had more strength invade pressure builds up.


Sent from my iPhone using Tapatalk Pro
 
Joshsmit56001 said:
Could you use these to switch from Ls tubing to 1/4" RO tubing?

https://www.bulkreefsupply.com/mur-lok-stem-adapter-tube-x-hose-stem.html

You could this and a coupling. Seems easier than the other connectors that have been mentioned.

Sent from my iPad using Tapatalk
Click to expand...

Sure, it would work fine. It's still a two piece connection though. The smooth side on that barb is a push to fit so it would still need to go into a john guest style push to fit connector. In the end it's basically the same.
 
LQT said:
That's weird... the links seem to be broken. I literally used them a week ago to order new tubing and parts.

L/S 17 equivalent tubing...
https://www.usplastic.com/mobile/catalog/item.aspx?itemid=25534

Barbed adapter for the quick connect fitting...
https://www.usplastic.com/mobile/catalog/item.aspx?itemid=36204

Quick connect fitting...
https://www.usplastic.com/mobile/catalog/item.aspx?itemid=42009

Hose clamps...
https://www.usplastic.com/mobile/catalog/item.aspx?itemid=34082
Click to expand...

Thanks, i just used them last week too. So it must have just been changed...
 
tkeracer619 said:
Sure, it would work fine. It's still a two piece connection though. The smooth side on that barb is a push to fit so it would still need to go into a john guest style push to fit connector. In the end it's basically the same.
Click to expand...



A simple John guest coupling would work fine


Sent from my iPhone using Tapatalk
 
Could you change a 100 rpm pump to a 600 rpm by just swapping the gear? I have a pump that is loud that is 600 rpm and I found a cheap new 100 rpm pump to swap with if possible.


Sent from my iPad using Tapatalk
 
Joshsmit56001 said:
Could you change a 100 rpm pump to a 600 rpm by just swapping the gear? I have a pump that is loud that is 600 rpm and I found a cheap new 100 rpm pump to swap with if possible.


Sent from my iPad using Tapatalk
Click to expand...

Brushed motors tend to be loud regardless of their RPM. If you find a 100 rpm pump that is the same (looks the same) as your 600 RPM pump, I am pretty sure you can swap the motor over to the 600 rpm one but unless the bearings are bad in your 600 rpm motor, the noise you are hearing is likely normal and or the result of the gears themselves. As such, swapping the motor over will likely not solve the noise issue.
 
slief said:
Brushed motors tend to be loud regardless of their RPM. If you find a 100 rpm pump that is the same (looks the same) as your 600 RPM pump, I am pretty sure you can swap the motor over but unless the bearings are bad in your 600 rpm motor, the noise you are hearing is likely normal and or the result of the gears themselves.
Click to expand...


It's a loud hum that is the noise at all RPM's. Would replacing brushes make any difference?


Sent from my iPad using Tapatalk
 
I asked a CP engineer about swapping between 100 and 600rpm. He said it was more than just gearing and couldn't be converted. I've never opened up a 100rpm model to compare gearsets however if you open up a 600rpm model it doesn't look like there would be enough room to physically fit a gear that would convert a 600rpm drive to a 100rpm drive.
 
I was inventorying and I have too many backups that I shouldn't!!
I just listed couple of brushless pumps on the selling forum.


Sent from my iPhone using Tapatalk
 
programming question within the masterflex pump. I have the 7523-60 and I thought it can dispense 0.6ml/min-3400ml/min but I cannot get it below 30ml. What am I doing wrong?

Sent from my SM-N950U using Tapatalk
 
Frank@wall said:
programming question within the masterflex pump. I have the 7523-60 and I thought it can dispense 0.6ml/min-3400ml/min but I cannot get it below 30ml. What am I doing wrong?

Sent from my SM-N950U using Tapatalk
Click to expand...


All depends on the tubing you are using. Which tube do you use?



Sent from my iPad using Tapatalk
 
24
da327e066c6e3560776c505f76d5295e.jpg


Sent from my SM-N950U using Tapatalk
 
You must log in or register to reply here.

Similar threads

FOX-FACE fanboy….
Calcium reactor components
Replies
7
Views
194
FOX-FACE fanboy….
FOX-FACE fanboy….
Chris Craig
Which Peristaltic Pump??
Replies
0
Views
41
Chris Craig
Chris Craig
five.five-six
Calcium reactor pH problem
Replies
3
Views
380
ct_vol
ct_vol
griss
Talk to me about Hydros
Replies
18
Views
366
Cruzersmith
C
O
Confused on Algae Reactor
Replies
7
Views
712
oceanfrank
O
Back
Top