Vertex Illumina Light Studio Programming Thread
- Thread starter Uncko Macko
- Start date
Uncko Macko
New member
Vertex released updates today.
http://www.vertexaquaristik.com/Pro...wnloads/tabid/581/language/en-US/Default.aspx
Let us know whats new. I won't be able to update for a few days
http://www.vertexaquaristik.com/Pro...wnloads/tabid/581/language/en-US/Default.aspx
Let us know whats new. I won't be able to update for a few days
gilbert2625
New member
hi there everyone,
just wanting to know if someone can help me with the cloud cover in settings.
How do you get the pads to do cloud cover pad by pad.kind regards gilbert.
just wanting to know if someone can help me with the cloud cover in settings.
How do you get the pads to do cloud cover pad by pad.kind regards gilbert.
alanbates12
New member
New Vertex owner, SR1500/260 also added 3 reds and 2 UVs. Going over a 24x24x72 180gal reef. Currently running T5s and have been for almost a year. Need suggestions of the power settings I should start off with. SPS, LPS, Inverts
alanbates12
New member
Thanks notclear. How is that 6' over your 72' tank. They told me to get a 5' over my 72'. They said the light spread would be more than enough. I don't want a lot of light spread out of the tank.
alanbates12
New member
can you post a photo of your tank notclear or a short video would be better.
alanbates12
New member
Nice video I've seen that on YouTube.
With the ’Ambient Light Range’ you can select LED-pad-area that shines during the night.
With ‘Apply Ambient Range’ this setting will be transmitted to the device.
Animadverto
New member
Does that mean the further the "Ambient Range" tabs are apart, the wider the coverage you'll get with the moonlight? There is not any icon of the led pads on the screen. I hit the "Moon" tab and proceeded to compose colors, but I didn't see any lights at all as I adjusted the intensity level. I was able to do expert programming just fine for the day setting. What am I doing wrong for the moon setting?
Can anyone point me to a manual for the Vertex desktop? I've found the firmware and have been playing around with the settings and all and think I get the basics for a program, but when I go to close it gives me a message saying actual startup settings not set or something along those lines. Any insight is appreciated, and my apologies if I overlooked something on here.
Animadverto
New member
I believe all you need to do is hit the "Start up setting" tab to the right of the right of the "Day & Moon Program" tab before quitting the program. This should store the fixture's setting to its flash memory.
I tried to upload the pdf manual here, but it said that I've exceeded the forum's limit for this type of file. If you really want it, PM me and I'll send it to you in an email.
My understanding is Yes (I have never tried though): if the slider on the top is at the farthest left and the bottom one at the farthest right, the moonlight covers the entire length of the fixture. And if now you just move the bottom slider to the middle, then the moonlight only covers the left to the middle of the LED fixture. So basically moonlight covers the area of the fixture in between the two sliders.
You can experiment this and post the result, thanks.
Last edited:
This explanation makes perfect sense based on my experiments last night for the first time after getting the light. I was playing around with the sliders and couldn't figure out why some were on and some were out when I was moving those darn sliders around. After reading this description that is exactly what was happening, good catch!
Animadverto
New member
Thanks for your help. You are right. The 2 slider tabs determine how wide the moonlight coverage will be once you click on the "Apply Ambient Range" button. The reason why I wasn't getting any moonlight was because I had both slider bars together one on top of another.
