anyone tried to using Jebo WP40?

Sacohen said:
It's an ES 750
http://www.apc.com/resource/include/techspec_index.cfm?base_sku=BE750G

D7A6454C78819EBC85257A700064EA09_EWAR_8XUPQL_f_h_500x500.jpg
Click to expand...

If you have the whole tank on this UPS (return pump, PS, controller, PHs...etc), according to the graph, at 150W this UPS will last about 22min.
 
Well it seems to have worked. I'm pretty sure I had a power outage yesterday at around noon for about 3 min and the tank was fine when I came home.

Worse thing that happened was the power supply for my laptop died. It is not on a UPS system. That's going to have to change when I have the money.
 
Tickyty said:
If you look at Jebao's naming convention this falls squarely in line with their other products. It is just a coincidence that it is similar to the MP40.
Click to expand...

Yep, I just cleaned a fountain pump that I've had for a couple years. To my surprise its a jebao wp-250
 
One month review on the WP40 pump

One month review on the WP40 pump

This is a little review of my WP40 pump after one month of use in my tank.
After placing the order on Fish Street Store, I received the pump in a week time, I was surprised by the fast delivery time.
It's been working flawlessly for more than a month.
At the beginning it was a little loud, but after one or two weeks working it becomes more silent. I can say it is completely silent now.
Im using the pump at 18V in ELSE mode and the flow is perfect for my 65 gallon tank. My BTA and my corals love the flow.
I would recommend this distributor, the link is on the original post, I have heard nothing but good things about their support on this product.
 
Installed 1 of my 2 WP40's finally in my 215 DT...totally silent and great flow on Else mode....I reiterate that the flow equates to a Tunze 6205....I have compared them side by side....although there is more control, support and service on the Tunze....(which goes without saying).
 
fltekdiver said:
Ok, didn't they just change their controllers to a newer version?
Click to expand...

Yes they did just change controllers or they added more functionality to it. It still looks like that. With all the units that were purchased over the last 5 months the person you got yours from most likely has not turned their inventory and that is why you will see the older ones for a while. FS is probably the best bet to get a new one.
 
For anybody still having problem with their night sensors, I have the solution. The ones they sent with the controllers didn't work in total darkness, but the replacement ones that I purchased did. Very expensive shipping so I searched for an alternative light sensor on ebay. Just got them today and they work fine in complete darkness. 30pcs for $3.27 from China. I'm not sure about linking to them, so search for this...
30PCS Photoresistor GL5537 LDR Photo Resistors. :beer:
 
I just replaced one wp40 with two wp25s in my 90g. I have them both in else and one dialed down to about 18 volts. The flow is very strong! It took me several hours to figure out where to place them so they werent destroying my lps' and softies. I think two wp40s would be overkill unless you dialed them way down.
 
You must log in or register to reply here.

Similar threads

P
Wave maker pump problem
Replies
1
Views
1K
rvitko
rvitko
P
Maxspect Gyre 300 series and ICV6 review
Replies
7
Views
4K
pisanoal
P
C
alternating flow on tunze 3 with y cable
Replies
10
Views
2K
rvitko
rvitko
slief
New Spectrapure Ultra Precise Top Off System. Good for Calcium Reactor Feed Pump Too
Replies
1
Views
693
slief
slief
A
water flow wave makers
Replies
1
Views
440
thegrun
T
Back
Top