ASM Skimmer FAQ's
- Thread starter NwG
- Start date
GoldStripe
New member
I'd go for the g6 for that size system
daytonreefRob
New member
Dubge said:
I am not sure if the Sedras come with different plugs (they may), but I know you can get Sedras that run on 220/240 Volts.
promod69camaro
New member
I purchased a G3 last week and need a little clarification on set up. I am making foam in the nozzle of the cup, but its not spilling over.
My water level is about 1/2 way up the first reducer. Am I supposed to raise it up to the nozzle in the cup (or second reducer / accumulator), leave it where it is, or lower it from where it is.
Your input is greatly appreciated.
My water level is about 1/2 way up the first reducer. Am I supposed to raise it up to the nozzle in the cup (or second reducer / accumulator), leave it where it is, or lower it from where it is.
Your input is greatly appreciated.
GoldStripe
New member
I've only had mine up for about a month so far but I have the bubbles come up about halfway into the riser tube in the cup itself. May a little less than half way. This will depend on how wet or dry you want to skim. Plus it took about a week for mine to actually start pulling the nasty's out.
promod69camaro
New member
I made an adjustment before I went to bed this morning. It seems to be pulling it out now. I did just what you said and set the foam about half way up the cup. I know this stuff is going to stink because its so thick.
I hope this will help me keep the alge blooms under control.
I hope this will help me keep the alge blooms under control.
GoldStripe
New member
It will definetly help. I know it helped with mine
tenshi
New member
Please do not trouble shot on this thread. This thread is intended as a FAQ page for ASM skimmers.
Please trouble shoot in the ASM Skimmer Club! thread. If you want to add information that you think other ASM owners might find helpful, please do so. Thank you.
Please trouble shoot in the ASM Skimmer Club! thread. If you want to add information that you think other ASM owners might find helpful, please do so. Thank you.
daytonreefRob
New member
Water Levels
While I have never seen anything publshed from All Seas Marine, I would recommend the following.
Minimum: 4 inches, you need to make sure there is enough water in your sump to cover the pump, don't want to run it dry.
Maximum: A few inches lower than the where the cone starts. If you place too much water in the sump, you will not be able to control the water level in the skimmer with the riser. Based on this, the maximum water level will vary depending on the skimmer model as they have differing heights.
I have seen some others suggest that 6-10 inches is where you need to be.
While I have never seen anything publshed from All Seas Marine, I would recommend the following.
Minimum: 4 inches, you need to make sure there is enough water in your sump to cover the pump, don't want to run it dry.
Maximum: A few inches lower than the where the cone starts. If you place too much water in the sump, you will not be able to control the water level in the skimmer with the riser. Based on this, the maximum water level will vary depending on the skimmer model as they have differing heights.
I have seen some others suggest that 6-10 inches is where you need to be.
NwG
New member
A little more info....
Ozone and ASM skimmers-
ASM skimmers are ozone safe. You should see no problems with running ozone in your ASM skimmer. I have been running 100mg/hr for about 6 months now with no ill effects. I have noticed a slight yellowing of the needlewheel of the pump the O3 os injected into.. But no brittleness or other problems... A LFS in my area has been running 200mg/hr in a early model ASM skimmer (~G4?) for over 4 years now.. The only noticable effect is a slight yellowing of the skimmer body.. Thos also may be due to the 400w MH that shines almost directly on it?
Nate D
Ozone and ASM skimmers-
ASM skimmers are ozone safe. You should see no problems with running ozone in your ASM skimmer. I have been running 100mg/hr for about 6 months now with no ill effects. I have noticed a slight yellowing of the needlewheel of the pump the O3 os injected into.. But no brittleness or other problems... A LFS in my area has been running 200mg/hr in a early model ASM skimmer (~G4?) for over 4 years now.. The only noticable effect is a slight yellowing of the skimmer body.. Thos also may be due to the 400w MH that shines almost directly on it?
Nate D
tenshi
New member
Gate Valve Mod on the G1, G1x, G2, and G3.
The G3 Gate Valve Mod works better if you put the elbow first, the gate valve 2nd, and the tee last. The Gate Valve Mod works better this way on the G1, G1x, G2, and G3 because of the height of the skimmer. You'll have more control of the foam height this way.
Tenshi
The G3 Gate Valve Mod works better if you put the elbow first, the gate valve 2nd, and the tee last. The Gate Valve Mod works better this way on the G1, G1x, G2, and G3 because of the height of the skimmer. You'll have more control of the foam height this way.
Tenshi
Similar threads
