ATI Powermodule Hybrid Club

[Keith@ ATI NA]

Thanks for the info. Some users have synced the Powermodule to their router. How hard is it to sync this to the router for time management

The difficulty is entirely based on your networking experience, experience with Linux and your level of understanding of German (or the use of google translate :spin3: ).

The instructions are still in German, however with the web tools and some basic networking knowledge it won't a problem.

If you cannot determine the IP address of a device on your network, this is not something you will likely have success with.

If you try and fail, you can factory reset your fixture, redo your setup procedure and reload your program. Not the end of the world, but a bit of a pain none the less.

 

[GQuinn]

PM sent

 

[Kengar]

I have older (2015 I believe), non-wireless powermodules. When power was off for couple hours, the time reset to 00:00. Is there anything to do to prevent that?

 

[Keith@ ATI NA]

I have older (2015 I believe), non-wireless powermodules. When power was off for couple hours, the time reset to 00:00. Is there anything to do to prevent that?

Depending on the generation there may be a firmware update available to fix it. If that still doesn't fix it it would require a new controller. Not the whole box, but just the control board (screen, buttons, brains). More than likely the firmware would do it if it needs updating.

Email me a photo of the sticker on the inside leg of your controller and we can take a look. I say email because RC won't let me PM you a firmware file it is not in the list of available extensions.

 

[Kengar]

Thanks, Keith.

Email just sent to customercare (chained onto our earlier conversation re replacing the LED clusters).

If it needs to go to new controller, is that something I can access by opening the box and removing the board to send in?

 

[Kengar]

Hi Keith,

Is there a way to delete some of the date points in Light Studio, so you don't need to program so many of them?

 

[Keith@ ATI NA]

Hi Keith,

Is there a way to delete some of the date points in Light Studio, so you don't need to program so many of them?

You cannot in Light Studio, you can however just group a bunch of them in the night time area.

On the WiFi Powermodule you can remove data points.

 

[Kengar]

You cannot in Light Studio, you can however just group a bunch of them in the night time area.

But I still have to drag all the dots down to 0 (and double-check by clicking on them to make sure they're at 0%) if I don't want any output associated with them, correct? In other words, there's no way to nullify a whole bunch of the time points all at once, is there?

On the WiFi Powermodule you can remove data points.

Oh, sure, rub it in!

 

[Keith@ ATI NA]

But I still have to drag all the dots down to 0 (and double-check by clicking on them to make sure they're at 0%) if I don't want any output associated with them, correct? In other words, there's no way to nullify a whole bunch of the time points all at once, is there?






Oh, sure, rub it in!

Nope
&
:lolspin:

 

[Kengar]

I should have bought the radions...... LOL!

I'm still in the process of setting things up, and with me cutting power to the units nightly (instead of having things set in Light Studio to turn on and off at certain times while ensuring burn-in, as we've discussed offline), they keep resetting and coming back on without the LEDs. But when I've run them with the LEDs (before the reset with power cycle), the overall effect has been really, really nice. Burn-in is almost done and I'll set and save profile then.

 

[takayan]

Hi guys,
I need your help.
I’m using 24” version of hybrid powermodile. Some of T5 did not light on, so I need to replace the T5 ballast. Where is the ballast? Is it still in the main fixture? Or it is now in the big box outside of the fixture?

 

[Keith@ ATI NA]

Hi guys,
I need your help.
I'm using 24" version of hybrid powermodile. Some of T5 did not light on, so I need to replace the T5 ballast. Where is the ballast? Is it still in the main fixture? Or it is now in the big box outside of the fixture?

Before jumping to conclusions about a bad ballast, I would recommend going through these steps to determine if it is a bulb or ballast giving you problems. While this video is for the SunPower, the content is applicable to your Powermodule.
https://www.youtube.com/watch?v=dGkvYqhdVSU&t

If you indeed determine it is the ballast, this is how you change it (again, while this is a T5 only Powermodule, the process is the same):
https://www.youtube.com/watch?v=qABYQiRLO6k&t

 

[JoshK6656]

The difficulty is entirely based on your networking experience, experience with Linux and your level of understanding of German (or the use of google translate :spin3: ).

The instructions are still in German, however with the web tools and some basic networking knowledge it won't a problem.

If you cannot determine the IP address of a device on your network, this is not something you will likely have success with.

If you try and fail, you can factory reset your fixture, redo your setup procedure and reload your program. Not the end of the world, but a bit of a pain none the less.

I would be interested in info on how to get this light on my network. Where is the guide to this?

Also, has anyone posted their schedules? Ever since installing this light, I have had major algae issues, and am curious in seeing others schedules.

 

[Keith@ ATI NA]

I would be interested in info on how to get this light on my network. Where is the guide to this?

Also, has anyone posted their schedules? Ever since installing this light, I have had major algae issues, and am curious in seeing others schedules.

Please shoot us an email and we can provide the information. Keep in mind it is a "use at your own risk" option.

 

[JoshK6656]

Please shoot us an email and we can provide the information. Keep in mind it is a "use at your own risk" option.

Done via the contact us form on your site (using the support options)

 

[Kengar]

Hi Keith,

If you see this first, please check your email. I have some questions re trying to replace the boards I have received. Thanks.

Ken

 

[Orcus Varuna]

ATI Powermodule Hybrid Club

[MENTION=364823]Keith@ ATI NA[/MENTION] Hey Keith I just moved and the root root admin login is no longer working to access the admin menus. Did they change the login? If so could you possibly pm me so I can get the light on my new WiFi network? The schedule is going out of time sync within a matter of a few days and is driving me nuts.


Sent from my iPhone using Tapatalk

 

[Orcus Varuna]

[MENTION=364823]Keith@ ATI NA[/MENTION] Hey Keith I just moved and the root root admin login is no longer working to access the admin menus. Did they change the login? If so could you possibly pm me so I can get the light on my new WiFi network? The schedule is going out of time sync within a matter of a few days and is driving me nuts.


Sent from my iPhone using Tapatalk

Never mind I figured it out. The new firmware apparently changes the root password to your user set password.


Sent from my iPhone using Tapatalk

 

[Keith@ ATI NA]

Never mind I figured it out. The new firmware apparently changes the root password to your user set password.


Sent from my iPhone using Tapatalk

Exactly, its either admin/admin or your chosen user/pass

 

[rugerjr81]

Beautiful setup. I love the ATI. My tank is only 18" cube though. So I ended up buying the Reefbrite MH/XHO 150 watt DE fixture. It's pretty sweet. I am loving to see all of this action of moving away from the heavy bandwagon of stacking expensive LED fixtures everywhere at $800 a pop, trying to get enough light eliminate hotspots, while acting like they are saving money. You may not have to buy bulbs, but drivers go out and fans go out. There is still maintenance with LED.


Sent from my iPhone using Tapatalk