Pacific Sun Kore 5th dosing Fan Club
- Thread starter Rudimenta
- Start date
serenity
Member
Imagine gum after chewing it for about 5 minutes. Incredibly pliable.
Sent from my iPhone using Tapatalk
This week i have been monitoring my Kore5TH doser and using a meassuringcylinder just for fun.
I´m using only pump 1,2+4 , since i ruled out pump 3 as unreliable (motor going slow)
Pump 1,2 set to 38ml and pump 4 to 35ml.
Here`s the funny thing , one day pump 2 only dosed about 3ml , and the next comming days pump 3 dosed about 3ml , and after that all three pumps dosed right again.
There is no slipping rollers , the motor goes for a second or two and then stops.
Think it is finaly time to put this in the bin now =)
I´m using only pump 1,2+4 , since i ruled out pump 3 as unreliable (motor going slow)
Pump 1,2 set to 38ml and pump 4 to 35ml.
Here`s the funny thing , one day pump 2 only dosed about 3ml , and the next comming days pump 3 dosed about 3ml , and after that all three pumps dosed right again.
There is no slipping rollers , the motor goes for a second or two and then stops.
Think it is finaly time to put this in the bin now =)
Griffter18
New member
New Doser
New Doser
Having just bought a 5th Kore and now read through all these pages I don't know what to expect but hopefully there's enough happy users to point me in the right direction for my queries.
Doser firmware has been updated to latest version via my IMac without problem.
I've calibrated each head and will run a series of test. On calibration I checked what had been saved and it matched my test programme so hopefully by end of tomorrow I should know if the Doser is dosing correct amounts under a single dose.
Q1. Can someone explain the different dosing option i.e. 1,2,c5 etc and what they provide.
Q2. If selecting more than one dose how do you ensure that doses aren't at the same time
Q3. Not to do with dosing but temp. The probe seems to have a little rubber cap on it. Should this be left on or taken off. Plan to use it for high/low alarm function as I use a temp controller.
Q4. I currently run a reefloat atu. The kore 5th has a built in atu function. How reliable have users found it with the optical sensor. Switching would save me a plug outlet and I can then move the reefloat to holiday duty to keep the atu filled.
Q6. What are the different flow rates used for and which am I better using. Will be using reeflowers all, calc,mag & elements + nopox. I have the dropper fitting as well as the standard one.
Q6. If using nopox do I need different tubing if so which type as there was only one kind in the box.
Q7. Some of the dosing heads make a slightly different noise. How do I check they've been assembled properly. Is there some instructions or a video I can watch
Q8. NRVs. Should they be installed pre or post Doser or should I run them at both ends
Q9. Unit came with some different tube for use in the dosing heads what are they for?
First impressions are its a very well built and good looking unit which just fits into the right cabinate of my RSR350
No problems connecting via Bluetooth with the iMac despite it being on floor above.
Firmware update was easy and only took a few mins.
Software and unit setup would benefit with a bit more user friendliness via the manual.
Connectivity seems ok and I'm using iPad to remote into the iMac and control the Doser without issue.
New Doser
Having just bought a 5th Kore and now read through all these pages I don't know what to expect but hopefully there's enough happy users to point me in the right direction for my queries.
Doser firmware has been updated to latest version via my IMac without problem.
I've calibrated each head and will run a series of test. On calibration I checked what had been saved and it matched my test programme so hopefully by end of tomorrow I should know if the Doser is dosing correct amounts under a single dose.
Q1. Can someone explain the different dosing option i.e. 1,2,c5 etc and what they provide.
Q2. If selecting more than one dose how do you ensure that doses aren't at the same time
Q3. Not to do with dosing but temp. The probe seems to have a little rubber cap on it. Should this be left on or taken off. Plan to use it for high/low alarm function as I use a temp controller.
Q4. I currently run a reefloat atu. The kore 5th has a built in atu function. How reliable have users found it with the optical sensor. Switching would save me a plug outlet and I can then move the reefloat to holiday duty to keep the atu filled.
Q6. What are the different flow rates used for and which am I better using. Will be using reeflowers all, calc,mag & elements + nopox. I have the dropper fitting as well as the standard one.
Q6. If using nopox do I need different tubing if so which type as there was only one kind in the box.
Q7. Some of the dosing heads make a slightly different noise. How do I check they've been assembled properly. Is there some instructions or a video I can watch
Q8. NRVs. Should they be installed pre or post Doser or should I run them at both ends
Q9. Unit came with some different tube for use in the dosing heads what are they for?
First impressions are its a very well built and good looking unit which just fits into the right cabinate of my RSR350
No problems connecting via Bluetooth with the iMac despite it being on floor above.
Firmware update was easy and only took a few mins.
Software and unit setup would benefit with a bit more user friendliness via the manual.
Connectivity seems ok and I'm using iPad to remote into the iMac and control the Doser without issue.
I'm using my Kore5th for almost 2 years now and don't have bad things to say. It might not be perfect but it works and has lots of good things.
One thing I'm disappointed in, it's still doesn't have mobile app that was promised long time ago. So any time I want to communicate with the doser, I have to turn my laptop on which is not a deal breaker, but mobile app would help a lot.
A lot of your questions could be answered just reading instructions
http://static.fachowcy.pl/files/3219127820/Kore_5th_manual_1.6a.pdf
Q1. Choose any of these options and you will see how software divides the doses over period of time. If you are dosing 120ml of solution and choose option 12, and your first dose let's say at 01:00, then doser will dose 10ml of the solution every 2 hours
Q4. The ATO works fine for me, never missed a beat, I'm very happy with it. I use optical sensor and it works great
Q7. Never worried about different noise coming from the heads. Once they are calibrated I check the calibration from time to time and if it stays the same there is nothing to worry about
Q9. The different tubing in the package is for fast flow. Once installed tubing on the heads wore out, I have replaced with included fast flow tubing and chose fast flow on the software. It doses liquid in fast flow more precise than with other tubing.
Play with the software and you should have no problems working this doser.
One thing I'm disappointed in, it's still doesn't have mobile app that was promised long time ago. So any time I want to communicate with the doser, I have to turn my laptop on which is not a deal breaker, but mobile app would help a lot.
A lot of your questions could be answered just reading instructions
http://static.fachowcy.pl/files/3219127820/Kore_5th_manual_1.6a.pdf
Q1. Choose any of these options and you will see how software divides the doses over period of time. If you are dosing 120ml of solution and choose option 12, and your first dose let's say at 01:00, then doser will dose 10ml of the solution every 2 hours
Q4. The ATO works fine for me, never missed a beat, I'm very happy with it. I use optical sensor and it works great
Q7. Never worried about different noise coming from the heads. Once they are calibrated I check the calibration from time to time and if it stays the same there is nothing to worry about
Q9. The different tubing in the package is for fast flow. Once installed tubing on the heads wore out, I have replaced with included fast flow tubing and chose fast flow on the software. It doses liquid in fast flow more precise than with other tubing.
Play with the software and you should have no problems working this doser.
PacSun Service
New member
Hello.
Let me answer for rest of questions.
2 - When You set how many doses per day You need You will see daily shedule of dosing.
3 - Cap should be on optical sensor. Please not remove it.
5 - Flow speed depend on single dose. If You will dose much fluid please choose fast flow. If You need drops please choose moderate or precise flow.
6 - Now in all dosing heads we use Pharmed Bpt tubbings which could dose nopox.
8 - NRV should be mounted on end of each tubbing output.
Best regards
Pacific Sun Service.
Let me answer for rest of questions.
2 - When You set how many doses per day You need You will see daily shedule of dosing.
3 - Cap should be on optical sensor. Please not remove it.
5 - Flow speed depend on single dose. If You will dose much fluid please choose fast flow. If You need drops please choose moderate or precise flow.
6 - Now in all dosing heads we use Pharmed Bpt tubbings which could dose nopox.
8 - NRV should be mounted on end of each tubbing output.
Best regards
Pacific Sun Service.
Griffter18
New member
2. I don't seem to see any detailed dosing schedule on the IMac software.
3. Question related to temp sensor not optical.
6. So are you saying that the clear tube from the Doser is also nopox compatible
8. No mention of NRVs in documents and I'm not sure which way round to mount them
Thanks
3. Question related to temp sensor not optical.
6. So are you saying that the clear tube from the Doser is also nopox compatible
8. No mention of NRVs in documents and I'm not sure which way round to mount them
Thanks
HelenofTroy
New member
Anyone know the differences in the 4 different models? There is the (1) main unit only, (2) regular, (3) pro, and (4) ultimate.
For the main unit only: does it have the temperature probe, and how finely can it dose?
For the main unit only: does it have the temperature probe, and how finely can it dose?
Przemek_PacSun
New member
Hi,
There is no Regular version available actually.
There are:
1) Starter Edition - include Kore 5th unit and power supply
2) Base unit(also called Main unit) - include doser, power supply, acrylic holder for tubings and 10m of additional tubing for doser connection
3) PRO - include above(like in Base) but also - optical sensor for ATO, DC pump for ATO, digital temperature sensor.
4) Ultimate - include everything like in PRO - but also AWC(automatic water change module with two DC pumps), top/bottle acrylic holder.
Regards
Przemek
There is no Regular version available actually.
There are:
1) Starter Edition - include Kore 5th unit and power supply
2) Base unit(also called Main unit) - include doser, power supply, acrylic holder for tubings and 10m of additional tubing for doser connection
3) PRO - include above(like in Base) but also - optical sensor for ATO, DC pump for ATO, digital temperature sensor.
4) Ultimate - include everything like in PRO - but also AWC(automatic water change module with two DC pumps), top/bottle acrylic holder.
Regards
Przemek
Przemek_PacSun
New member
In this week we release app for Diuna T5 lamps, next week we should finish for SMR(Pandora Hyperion S/Metis Hyperion S) and last - for Kore5th.
But please remember that this application will have limited functionality - Customer will can check bottle status, adjust dosing amount per day in each channel separately and do basic adjustment for ATO. For more advanced settings (like calibrations, advanced dosing settings etc) PC/Mac application should due used.
Regards
Przemek
But please remember that this application will have limited functionality - Customer will can check bottle status, adjust dosing amount per day in each channel separately and do basic adjustment for ATO. For more advanced settings (like calibrations, advanced dosing settings etc) PC/Mac application should due used.
Regards
Przemek
Hello all,
I just want everyone to know that my doser is working again. I am in the process of calibrating and hopefully things will be off and running. Kore 5th tech folks worked with me. The problem was not bluetooth, nor the power supply. It ended up being the motherboard in which I sent back and they fixed free of charge. (Despite being out of warranty,which I consider fair since I have not been able to use much during the warranty)
The issue may have been created by me. Generally from what was explained that this may have been caused by plugging an item in one of the back ports without turning the unit off first. I may have done this when trying to set up the optical sensor.
Although it took quite some time to get the motherboard back from Poland, I am excited to give this another try as my aquarium is doing well and it really would be nice to automate my two part schedule. I am in the process of calibrating and hope that the product will give me years of service as it out of the warranty date.
At this point I was able to connect to bluetooth easily, and since I had older firmware I connected via emergency tab and was able to upgrade the firmware. It takes a bit of time but all went fine.
My hope is to have this set up shortly and will monitor the dose a couple of days before allowing it to dose the aquarium.
-Ed
I just want everyone to know that my doser is working again. I am in the process of calibrating and hopefully things will be off and running. Kore 5th tech folks worked with me. The problem was not bluetooth, nor the power supply. It ended up being the motherboard in which I sent back and they fixed free of charge. (Despite being out of warranty,which I consider fair since I have not been able to use much during the warranty)
The issue may have been created by me. Generally from what was explained that this may have been caused by plugging an item in one of the back ports without turning the unit off first. I may have done this when trying to set up the optical sensor.
Although it took quite some time to get the motherboard back from Poland, I am excited to give this another try as my aquarium is doing well and it really would be nice to automate my two part schedule. I am in the process of calibrating and hope that the product will give me years of service as it out of the warranty date.
At this point I was able to connect to bluetooth easily, and since I had older firmware I connected via emergency tab and was able to upgrade the firmware. It takes a bit of time but all went fine.
My hope is to have this set up shortly and will monitor the dose a couple of days before allowing it to dose the aquarium.
-Ed
serenity
Member
Whooo hooooo!!! Get that baby fired up!!
Damn, this is just what I was hopping for!!!
https://************.com/2017/03/17/alkalinity-monitor-coming-soon-to-pacific-sun-kore-5th-doser-ecosystem/
https://************.com/2017/03/17/alkalinity-monitor-coming-soon-to-pacific-sun-kore-5th-doser-ecosystem/
Only 450 euros according to pacsun's FB page. With current exchange rate and VAT factored in that beats the hell out of paying $1250 for kh guardian. If Kore 5th is doing all of the "controller" part, then that make price makes sense. I am hopping it has its own pumps and doesn't require a whole Kore 5th to itself to function.
Przemek, kudos to you guys at Pacific Sun!!!
Sent from my STV100-1 using Tapatalk
