anyone tried to using Jebo WP40?

Over $200 for a piece of non-essential equipment is expensive in my book. I'm only 25 and have a ton of student loans. My build is very budget constrained. I'd rather put that $200 into some new coral frags. My tank is so bare right now. I haven't been able to restock since my sand bed caused a soft crash.
 
So I'm told, I'm just not sold on them. I don't use high end controllable leds or dosers of any sort. It would be nice to have another layer of protection should the thermostats in my heaters fail. Other than that, I can't see my setup benefiting from one much.
 
I got my WP-40 today in the mail and they sent two light sensor with it.
I can say light sensor is working fine and make a nice size wave in 47 1/2 "L x 18 1/2" W x 25 1/2 " T tank.
DSC00020.JPG

DSC00023.JPG

DSC00001.JPG
 
Good new Apex users!

I was able to successfully ditch the Jebao controller and completely control my wp40 with the RA Jebao connection cable to my Apex. All I had to do was remove the RA connector and rewire it for a ethernet (RJ45 connector). Very simple and now I have complete control! Thanks Roberto for your assistance!
 
jrp1588 said:
Over $200 for a piece of non-essential equipment is expensive in my book. I'm only 25 and have a ton of student loans. My build is very budget constrained. I'd rather put that $200 into some new coral frags. My tank is so bare right now. I haven't been able to restock since my sand bed caused a soft crash.
Click to expand...

Hopefully your heater never sticks and kills your entire tank along with the $200 frags you purchased. Just busting your chops. Controller are almost essential IMO.
 
hollback said:
Good new Apex users!

I was able to successfully ditch the Jebao controller and completely control my wp40 with the RA Jebao connection cable to my Apex. All I had to do was remove the RA connector and rewire it for a ethernet (RJ45 connector). Very simple and now I have complete control! Thanks Roberto for your assistance!
Click to expand...

Awesome. Now you guys can join the fun.

Roberto is awesome isn't he?

Have fun messing with your controlled pump.
 
hollback said:
Good new Apex users!

I was able to successfully ditch the Jebao controller and completely control my wp40 with the RA Jebao connection cable to my Apex. All I had to do was remove the RA connector and rewire it for a ethernet (RJ45 connector). Very simple and now I have complete control! Thanks Roberto for your assistance!
Click to expand...


Awesome!!! I had a new VDM module as well as the RA harness to takle this project but between my 17 month old, the new house I've been in for a month and a large project at work I haven't had the time to. The only question I had was which of the wires on the RA harness is the ground and which is the 0-10 variable voltage wire.
 
SeedlessOne said:
Awesome. Now you guys can join the fun.

Roberto is awesome isn't he?

Have fun messing with your controlled pump.
Click to expand...

I already have two Tunze 6105's being controlled so I'm just adding this to the mix.

bu11itt said:
Awesome!!! I had a new VDM module as well as the RA harness to takle this project but between my 17 month old, the new house I've been in for a month and a large project at work I haven't had the time to. The only question I had was which of the wires on the RA harness is the ground and which is the 0-10 variable voltage wire.
Click to expand...

On the RA connector, the red striped wire was the 0-10v and the white wire was the ground.
 
So I emailed FS today about WP-40 it came with a UK power cord not a US power cord and they emailed me back ask if i can take a photo of the power cord I side sure and send them some photos.I get a phone call from Eric Wong head of FS and he apologize about the power cord and side they will mail me out a new power cord and some light sensor and if I need any help or if anything go wrong with the pump that will replace it and he gave me his phone number and email address. So if any want Eric Wong email address pm me
 
Got mine today and running it in a 72 gallon bow at 16v. I'm getting about a 1" wave, it's making me a little nervous but I love the action. Might have to hook it up to the reef angel and play around with it next week. Also I can't even hear it unless I put my ear right next to it. Very happy with this purchase.
 
Last edited:
Fish street needs to get back to me soon. I've emailed them a couple if times. Mine has been stuck in San Fran for 13 days, been 21 days since it had been shipped. I'll probably end up requesting a refund thru PayPal if it doesn't come soon.
 
I would file a claim, he doesn't answer you because he doesn't have an answer to give.

He has answered me twice in the last 24 hours.
 
Refund

Refund

non-ricer said:
Fish street needs to get back to me soon. I've emailed them a couple if times. Mine has been stuck in San Fran for 13 days, been 21 days since it had been shipped. I'll probably end up requesting a refund thru PayPal if it doesn't come soon.
Click to expand...


So you want a refund from a company for delayed shitting? Hve you tried calling the shipping agency instead? I've shopped quite a bit through the last years with different online stores and my impresion is that Eric is one of the better ones. Aslong as you can send him a good reason or a picture, theres service and quick solutions from him.
 
You must log in or register to reply here.

Similar threads

P
Wave maker pump problem
Replies
1
Views
1K
rvitko
rvitko
P
Maxspect Gyre 300 series and ICV6 review
Replies
7
Views
4K
pisanoal
P
C
alternating flow on tunze 3 with y cable
Replies
10
Views
2K
rvitko
rvitko
slief
New Spectrapure Ultra Precise Top Off System. Good for Calcium Reactor Feed Pump Too
Replies
1
Views
677
slief
slief
A
water flow wave makers
Replies
1
Views
426
thegrun
T
Back
Top