Sam's Oceanic 120

[projectsWithSam]

1/28/23
Posted a bunch of new products!

ParlaScrubber 90mm CO2 Cap

This Skimmer cap was designed for the AquaMaxx Bullet 2 Hang-On Back Skimmer.

parlaquatics.com

for the Aquamaxx Bullet 2 Hang-On Back Skimmer

4" Filter Sock Cup - Filter Sock Replacement System

Filter Sock cup for 4" Filter Sock holders. Getting tired of dealing with those huge filter socks? Look no-further... There are two ways to get the perfect filtering replacement for felt or mesh filter socks: Complete: Use some filter floss. Use included template and cutout as many disks of...

parlaquatics.com

EcoTech XR15 Light Shade Model 1

This light shade is designed for the XR15 aquarium light by EcoTech. It works on gen 3-6 XR15s. Its been tested on the Gen6 version but will also fit many other XR15 models.

parlaquatics.com

Twist nut for 4545 extrusion - 6mmTube (12 pack)

This small piece of plastic twists securely into 4545-style aluminum extrusion and allows 5.5 to 6.5mm aquarium airline tubes to be managed.This part, once twisted into place on the extrusion, can support four tubes and keep them well-organized while still leaving them visible. Strong PETG+...

parlaquatics.com

Twist nut for 4545 extrusion - 6mmTube Long (12 pack)

This small piece of plastic twists securely into 4545-style aluminum extrusion and allows 5.5 to 6.5mm aquarium airline tubes to be managed.This part, once twisted into place on the extrusion, can support four tubes and keep them well-organized while still leaving them visible. Strong PETG+...

parlaquatics.com

Twist nut for 4545 extrusion - Hook (12 pack)

This small piece of plastic twists securely into 4545-style aluminum extrusion and allows wires or similar to be cradled in-place.This part, once twisted into place on the extrusion, can support many wires and keep them relatively well-organized while still leaving them accessible. One-hand...

parlaquatics.com

Twist nut for 4545 extrusion - ZipTie (12 pack)

This small piece of plastic twists securely into 4545-style aluminum extrusion and allows wires or similar to be Zip-Tied in-place.This part, once twisted into place on the extrusion, can have up to two zip-ties securing things. One-hand operation for those tough to access places.Convenient...

parlaquatics.com

Twist nut for 3030 extrusion - 6mmTube Long(12 pack)

This small piece of plastic twists securely into 3030-style aluminum extrusion and allows 5.5 to 6.5mm aquarium airline tubes to be managed.This part, once twisted into place on the extrusion, can support four tubes and keep them well-organized while still leaving them visible. Strong PETG+...

parlaquatics.com

 

[projectsWithSam]

2/1/23
A pal hooked me up with my first torch and a couple of digi/birdsnest

frag tank shots: (after vacuuming up all the cyano)

random shots:

The green flash 1 minute before lights out...

 

[projectsWithSam]

Just refilled my Kalkwasser reactor because I've seen my alk steadily drop.
Steps to refill a ParlAStir:
1) Disconnect doser tube and bend over into a bucket.
2) Drain about a pint of the solution into a container.
3) Add about a cup of Pickling Lime to the container and stir.
4) pour solution into the bottom of the stirrer via funnel attached to a tube.
5) Top off stirrer with RODI

Got the BattleCorals 2023 Growout Competition graphics printed and up!

El Torcho is doing well I think!

 

[projectsWithSam]

1/5/23
My ParlAScrubber is still kicking but!

I'm getting tempted scrap the refugium and make a ParlAlgaeScrubber. haha. stating to come into my own on the product names!

 

[projectsWithSam]

1/8/23
finally able to get it to print! bed adhesion was not working on the PEI springsteel so I had to go back to basics with glass & glue.