Krazie4Acans
New member
I wasn't sure if you meant 1 puck or 1 light. 1 Radion light has two pucks in it. So 1 puck basically means you are running half a Radion. lol Hopefully some of all that helps.
DIY LEDs with Radion Pro G2 pucks?
- Thread starter rcmike
- Start date
I wasn't sure if you meant 1 puck or 1 light. 1 Radion light has two pucks in it. So 1 puck basically means you are running half a Radion. lol Hopefully some of all that helps.
djmx2002
Premium Member
Ligershark
Member
A little look on my fixture
I've finished it. I'll try it next days...
Very nice clean build, just curious about the methodology behind the fan placement. Are those fans blowing down or up? I was under the impression fans should be blowing onto the heatsink to keep it cool. Is your method to removing warm air by blowing it down and out of the housing? Just curious as I'm getting ideas for my next build.
thanks
I am reading the threads, Has anyone purchase the extra Semileds Leds and soldered them to the G2 PCB's using a hot plate? Would I need to remove the 0 Ohm resisters if I add LED's? Would this work?
I have 2 Radion G2's and it appears the pads are on the PCB's for the extra LED's. I would like to upgrade them myself. It seems like I can do 2 fixtures for about $90.00.
Thanks for your help in advance,
Tony
I have 2 Radion G2's and it appears the pads are on the PCB's for the extra LED's. I would like to upgrade them myself. It seems like I can do 2 fixtures for about $90.00.
Thanks for your help in advance,
Tony
Cables and Connectors for LED Power
Cables and Connectors for LED Power
I'm not sure how many conductors you are looking for but I found these available at a great price and they are fully waterproof(except the ends connected to the Driver and LEDs). There are a lot fo options for this kind of cable. The ones I linked are for 8 conductor(4 strings) at I think 24 Awg. I calculated that for my 30 CREE XT-E @ 1 Amp that 24 AWG is the correct sizing. There are 2 separate links ... 1 for the cable that runs between the driver and LEDs and the other for the pre-wired connectors at each end. Very convenient and has the nice finished look people are looking for.
Link to Cable:
http://www.ebay.com/itm/171629259831?_trksid=p2060778.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
Link to Connectors used at both ends:
http://www.ebay.com/itm/171570268125?_trksid=p2060778.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
Cables and Connectors for LED Power
I'm not sure how many conductors you are looking for but I found these available at a great price and they are fully waterproof(except the ends connected to the Driver and LEDs). There are a lot fo options for this kind of cable. The ones I linked are for 8 conductor(4 strings) at I think 24 Awg. I calculated that for my 30 CREE XT-E @ 1 Amp that 24 AWG is the correct sizing. There are 2 separate links ... 1 for the cable that runs between the driver and LEDs and the other for the pre-wired connectors at each end. Very convenient and has the nice finished look people are looking for.
Link to Cable:
http://www.ebay.com/itm/171629259831?_trksid=p2060778.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
Link to Connectors used at both ends:
http://www.ebay.com/itm/171570268125?_trksid=p2060778.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
Fixture in action... only 20% power
Absolutely the best DIY fixture I've seen made so far! Great Job!!! It looks really professional. Now that it's done, is there anything you'd do differently, looking back?
