Major Product Announcement
- Thread starter AQD_ottawa
- Start date
AQD_ottawa
New member
Being shipped to him next week
AQD_ottawa
New member
as far as I am aware yes
AQD_ottawa
New member
There is no part number as yet.
email me and I will sort out one for you we have been supplied a few FOC by GHL so just the shipping costs are to be paid to you.
EMAIL NOT PM
email me and I will sort out one for you we have been supplied a few FOC by GHL so just the shipping costs are to be paid to you.
EMAIL NOT PM
AQD_ottawa
New member
No but please read the VERY important warning note that is in the to of your ProfiLux as to where to plug the power bar.
Failure to adhere to this will invalidate the warranty.
Please let us know which port you have plugged into.
Best thing to do is kick back read the manual and start from the beginning step by step set up, dont rush into anything too hasty
If you are referring to the Ai cable it can only plug into one port, the RS232 port. For Ai you also need to be using V4.01 desktop and firmware also
Here to help
Best wishes
Michael
Failure to adhere to this will invalidate the warranty.
Please let us know which port you have plugged into.
Best thing to do is kick back read the manual and start from the beginning step by step set up, dont rush into anything too hasty
If you are referring to the Ai cable it can only plug into one port, the RS232 port. For Ai you also need to be using V4.01 desktop and firmware also
Here to help
Best wishes
Michael
Definately plugged into the correct port on the profilux unit. I was referring to the AI unit, there are two inputs for power, and two inputs for data. I'm assuming I can use either, but am not sure.
I um running version 4 on unit, and 4.01 desktop software...(yet to be able to connect to software though). Shouldn't the light demo be able to run the AI though?
Stoneyscoral
New member
Jane, I presume you have your cable(I sent it last Thursday). Did you try it out yet?
Pics?
Pics?
Matthias Gross
.Registered Member
you need firmware version 4.01 for the unit
then you have the option "special lamp" like Todd mentioned
with version 4.01 you can alter the settings only on the device itself
4.02 is in development with AI support in ProfiLuxControl
then you have the option "special lamp" like Todd mentioned
with version 4.01 you can alter the settings only on the device itself
4.02 is in development with AI support in ProfiLuxControl
JPagliai
New member
Yes, I did get the cable. Thank you very much!!!
I haven't hooked it up yet. I'm still waiting for hubby to finish plumbing the tank. If I have time this weekend, I may hook up the lights on the empty tank just to see how they look. I'm very anxious to get these lights up and running.Specs
Specs
Hi Chaps
A Very interesting thread indeed! I must say that I'm very interested in these AI units, but rather disconcerted about the lack of information about them. Chris - Are the specs availible from the AI website - Cause I don't even see this particular product on there??
As for many people, cost is a considerable factor when running a large marine aquarium. I myself have been thinking about going down the LED route from both a cost saving perspective and a saving the planet perspective! Hence I would be very interested to calculate the running costs per module, and the stats on illumination / penetration in comparison to say a 150 Watt Halide. But I can't find hardly any stats on this.
CHRIS - Please HELP
As I need to justify spending a HUGE amount of money to the Mrs, and won't be able to do so without the figures to back it up
So to summarize - Please post a full spec sheet for these units, along with some stats on power consumption etc......
Thanks Chaps
Specs
Hi Chaps
A Very interesting thread indeed! I must say that I'm very interested in these AI units, but rather disconcerted about the lack of information about them. Chris - Are the specs availible from the AI website - Cause I don't even see this particular product on there??
As for many people, cost is a considerable factor when running a large marine aquarium. I myself have been thinking about going down the LED route from both a cost saving perspective and a saving the planet perspective! Hence I would be very interested to calculate the running costs per module, and the stats on illumination / penetration in comparison to say a 150 Watt Halide. But I can't find hardly any stats on this.
CHRIS - Please HELP
As I need to justify spending a HUGE amount of money to the Mrs, and won't be able to do so without the figures to back it up So to summarize - Please post a full spec sheet for these units, along with some stats on power consumption etc......
Thanks Chaps
