ReefingBuddha
New member
Received mine today. Any idea when version 4.03 will be finalized? How stable are BETA versions?
OK, setting up my WMX and here is where I hit a snag.
Downloaded and updated the 4.03 firmware, no problem.
I am on page 4 of the WXM instructions where is says to upgrade the firmware on the MP40w to ver 3.1.
The instructions say to "Use the Setup> Module Setup> Config Module Menu. Select WXM and then do a WWD Update"
My Module setup after the firmware update has WMX in a drop down box and "update firmware", but nothing about a "WWD Update". I did the firmware upgrade for the WMX, but it does not appear to be communicating with the MP40w. The greeen "wireless status" light is on.
On the MP40w, I held down the mode and setup keys while powering on, but instead of red/white like the instructions say, I get red/blue. I press the set key like step C indicates, but no blinking blue light appears.
Anyone install their WMX yet on a MP40w and figure out the firmware download to the MP40w.
Milkman, youre going to have to explain how to do it. I tried doing this yesterday at home and this morning before i left to work without success.
How many feet apart would you say you have to have the drivers from the module? Do you only do one pump at a time or something? I have 2 MP40W ES vortechs and one MP10W ES pump as well
Can someone think of how to slow down the vortech during feed (like 10% constant), then after feed is complete run Nutrient transport for 20 minutes, then resume normal programming?
I've got:
Fallback ON
Set OFF
If Time 11:00 to 23:00 Then Reef_C_D
If Time 23:01 to 10:59 Then Lagoon_N
If FeedA 000 Then Slow
But how to make it do Nutrient for 20 minutes before resuming the time based scheduling?
Why not make some virtual outlets?
Can someone think of how to slow down the vortech during feed (like 10% constant), then after feed is complete run Nutrient transport for 20 minutes, then resume normal programming?
I've got:
Fallback ON
Set OFF
If Time 11:00 to 23:00 Then Reef_C_D
If Time 23:01 to 10:59 Then Lagoon_N
If FeedA 000 Then Slow
But how to make it do Nutrient for 20 minutes before resuming the time based scheduling?
I created a Profile called FEED and set the speed at 10%, then replace "Slow" with FEED. Not sure what the pump settings are for nutrient export because I don't have the ES, but I bet it can be replicated.
Milkman, youre going to have to explain how to do it. I tried doing this yesterday at home and this morning before i left to work without success.
How many feet apart would you say you have to have the drivers from the module? Do you only do one pump at a time or something? I have 2 MP40W ES vortechs and one MP10W ES pump as well
I'm running the latest 4.03.
I just plugged my WXM in and I'm getting an error on Firmware Update Step 1 - Upgrading my WWD pump.
Following step 1 on the display, when I click on the 'WWD Update' it displays this:
WWD Update
Update Error: 0
I've tried multiple times, but get the same error.
Any thoughts?
I was getting the same thing for a while. Try updating all firmware including the WXM to the latest beta. After that, unplug the WXM module for 10 seconds, plug it back in. Make sure the LED lights on the WXM module are solid green before beginning the update.
I have updated to the latest overall firmware.
When I look at the module list, thay all report OK.
Specifically the WXM:
SWRev 004(OK)
Then below that is RF info:
Rev1.1, RF Rev 1.2 (1,0,0,0)
Is this what is listed in your module section?
PS. I also, have a solid green light on the RF indicator.