ATI Powermodule Hybrid Club
- Thread starter rodneyri
- Start date
Logzor
New member
I'm about 1.5 hours away right off of I-71 in the Cincinnati area.
Last edited:
Mikebuurskov
New member
My pc and the ballast from the lamp tells That the med Chanels is 72.3° so they dont start at all. And lamp is off the tank so its not hot at all.
Firmware is updated.
Its a powermodule 8x39w and 2x75
Firmware is updated.
Its a powermodule 8x39w and 2x75
h3dgehog
Member
Can you elaborate what you mean by you tank liking the t5 better than the hybrid?
hbrochs
New member
My rockwork is kinda centered down the four foot length of my tank. This brings my sps pretty high right under the leds (which are centered on the Powermodule). I feel like I was always walking the line with burning my corals with the Sunpower. I'm not great at programming the leds on the Powermodule so I'd just raise the fixture if it looked like the corals needed that.
With the Sunpower, I've been able to slowly lower the fixture to about 8 inches over the water and my corals seem to be growing faster.https://vimeo.com/193381640
I feel like the royal blue led bars in the front and back of the Sunpower will give nice dawn and dusk actinic pop.
Will give an update when I get those hooked up.
Sent from my iPhone using Tapatalk
With the Sunpower, I've been able to slowly lower the fixture to about 8 inches over the water and my corals seem to be growing faster.https://vimeo.com/193381640
I feel like the royal blue led bars in the front and back of the Sunpower will give nice dawn and dusk actinic pop.
Will give an update when I get those hooked up.
Sent from my iPhone using Tapatalk
h3dgehog
Member
So in other words, the LEDs in the PM were too powerful/concentrated that it caused issues?
Logzor
New member
See my post above removing reflectors, no official response from ATI yet. I think it could help some users with this issue.
h3dgehog
Member
Correction. I menat 8 bulb unit.
I get some monster par with my 250W radium bulb and was looking to the ATI PM for better spread (hate how some of my SPS colonies are growing towards the center and not branching out evenly). However, I don't want to add even more par than what my Radium bulb puts out because I don't want to have my lights hanging any higher.
I get some monster par with my 250W radium bulb and was looking to the ATI PM for better spread (hate how some of my SPS colonies are growing towards the center and not branching out evenly). However, I don't want to add even more par than what my Radium bulb puts out because I don't want to have my lights hanging any higher.
biecacka
Active member
What sort of numbers are you getting from your radium? Not to derail the thread. But I run a radium in my tank, 24 inches deep and 12 inches off the water. I was going to try to borrow a par meter to see.
Back to the topic, yes an 8 bulb fixture makes more sense than a 10 bulb. Maybe a different reflector could even out your spread though?
Corey
Back to the topic, yes an 8 bulb fixture makes more sense than a 10 bulb. Maybe a different reflector could even out your spread though?
Corey
h3dgehog
Member
Last I had my radium ~7" from the water surface with a ~19" tank height, I think I got ~400 par on the sandbed.
Between the 4 bulb vs 8 bulb ATI PM, is 8 bulb the way to go? Only thing is that the fixture would go over the tank since the tank dimensions are a bit smaller.
BeanMachine
Active member
Would you mind posting a pic of your setup with the Kessils? I'm interested in doing the same thing. I have a 72" x 36" tank and got the 8 lamp PM.
Callum96
New member
ive been looking into getting myself an ATI powermodule T5 hybrid and remember speaking to someone a few months ago that really knows his stuff on these lights and he said my four foot unit over five foot tank (1500mm x 50mm x 55mm) wasn't ideal but I could probably get away with it. Well, Ive been thinking about trying to get a unit to cover the whole tank which the 8x80w + 4x75w would fit perfectly being 1473mm x 517mm. This unit however just seems to me like it would be massive overkill for a Red Sea reefer 450 I think I'd be better off with the 54w unit but then that's only 4 foot (ish) where the tank is 5 so I'm a little confused at which one to go for.
There is then also the 4 x 80w unit but then that limits me with the t5 tubes and I know that a 8 tube unit would probably be better than 4, better to have too much and can be dimmed than not enough I guess?
I wish they did a 6 x 54w unit with the leds that's five foot as for my tank that would be perfect in my opinion.
Just looking for for a bit of advice really as I don't want to mess this up with the right unit being an absolutely crucial part of the tank which will be purely SPS with a couple of clams and a gigantea anemone all which require strong lighting.
There is then also the 4 x 80w unit but then that limits me with the t5 tubes and I know that a 8 tube unit would probably be better than 4, better to have too much and can be dimmed than not enough I guess?
I wish they did a 6 x 54w unit with the leds that's five foot as for my tank that would be perfect in my opinion.
Just looking for for a bit of advice really as I don't want to mess this up with the right unit being an absolutely crucial part of the tank which will be purely SPS with a couple of clams and a gigantea anemone all which require strong lighting.
Ourlittlereef
New member
My new tank build is the marineland deep dimension 300 gallon, which sounds like the same tank dimensions you have. i'm looking at a t5/led combo, and have been debating between the ATI PM and Giesemann Aurora 60". How is the ATI 8 bulb working for you? My biggest concern with the Giesemann is that the depth front to back might not get enough coverage.
Ourlittlereef
New member
My new tank build is the marineland deep dimension 300 gallon, which sounds like the same tank dimensions you have. i'm looking at a t5/led combo, and have been debating between the ATI PM and Giesemann Aurora 60". How is the ATI 8 bulb working for you? My biggest concern with the Giesemann is that the depth front to back might not get enough coverage.
Similar threads
