GHL Doser 2 Owners Club

new doser-2 owner looking for wi fi direction?

new doser-2 owner looking for wi fi direction?

Have new doser 2! Very excited. Just found this forum.
Looking for someone who would be kind enough to point me in the right direction, where I can find some basic step by step to get this pump going via my home wi fi or any other wireless that works. I have home win pc (7/64). My lights and controller were ease to connect where I can use my droid tab and phone to control. But it seems this doser requires some advanced IT know-how???

I am connected via usb to pc in my office (not near tank). Have advance manual but there are a number of different options to follow. Not sure which to follow with all the acronyms...?

Thanks in advance to anyone who can point me in the right direction...Jim
(wish they had some support)
 
Hiya

best place to always start is on the support forum www.aquariumcomputer.com the techs can walk you through.

go to the forum (english) and sign up, you need to wait maybe 24 hours for the auto spam bot to accept you, if not accepted within 24 hours then pm me.

we cant offer much support here as it would make the whole forum become a support site when we already have a dedicate one. Hope thats ok

all the best
Michael
 
mhx file

mhx file

Attempting to get wi fi connected. Noticed that since I started attempting a few days ago firmware 01 is available. I have 1.00 and 1.00 manual.
Tried downloading 1.01 but comes as a mhx file which my win pc does not recognize or open? How do I get mhx file open for firmware upgrade. Frustrated at support over at GHL which is a mystery to me.
 
Attempting to get wi fi connected. Noticed that since I started attempting a few days ago firmware 01 is available. I have 1.00 and 1.00 manual.
Tried downloading 1.01 but comes as a mhx file which my win pc does not recognize or open? How do I get mhx file open for firmware upgrade. Frustrated at support over at GHL which is a mystery to me.

JimEvt,

1.02 is the present firmware for the Doser 2. That'll be in included with Control Center V 1.0.6.0.

After GHL Control Center V 1.0.6.0 has been installed. You'll find Firmware V 1.02. within folder - Program Files (x86)\ GHLControlCenter_V1060\ Firmware\ GHL Doser 2

Follow the information on GHL's forum for guidance.
http://forum.aquariumcomputer.com/showthread.php?9563-Doser-2-firmware-1-02-update-failed
 
thanks-followed instructs for firmware update. All fine, but when I begin the update, adobe flash opens and I get an 'access denied' message. Where does one get help.
 
Hiya

best place to always start is on the support forum www.aquariumcomputer.com the techs can walk you through.

go to the forum (english) and sign up, you need to wait maybe 24 hours for the auto spam bot to accept you, if not accepted within 24 hours then pm me.

we cant offer much support here as it would make the whole forum become a support site when we already have a dedicate one. Hope thats ok

all the best
Michael
 
Does any one have problems with the tubes getting pushed off the connecter part? I have tried strip ties, but still the tube get pushed off.
 
Disconnecting itself from the novoprene tubing, no. Is there any slack or do you have a tight line from the pump heads to your dosing containers?
 
Disconnecting itself from the novoprene tubing, no. Is there any slack or do you have a tight line from the pump heads to your dosing containers?

yes there is some slack, as the unit is under my system, and has to pump it up to it, as i have no sump. I have tryed using backflow valves. Also its only one of the pumps that does it. There dosent seem to be any resistance in the tube, i can easely blow air through it, and the liquid seems to run throught it as the same speed as the other pumps (when you calibrate it). The novoprene tubing isent disconection it self, its my tubing, that is put onto that small plastic hose connecter part, that keeps getting pushed off.
 
Back
Top